Partitionieren unter FDISK

Partitionieren unter FDISK


Nach dem Starten des Programms wird man gefragt, ob man mit oder ohne
"Unterstützung" in FDISK arbeiten möchte.
MIT Unterstützung bedeutet, daß die Festplatten in FAT32 (Standard) partitioniert
werden. OHNE Unterstützung werden sie in FAT16 (meist bei älteren
Rechner) partitioniert.

Daraufhin stehen einem folgende Optionen zur Auswahl:

(1) Dos-Partition oder logisches Dos-Laufwerk erstellen
|
-- (1) Primäre Dos-Partition erstellen
-- (2) Erweiterte Dos-Partition erstellen
-- (3) Logisches Dos-Laufwerk in der erweiterten Dos-Partition erstellen

(2) Aktive Partition festlegen
(3) Partition oder logisches Dos-Laufwerk löschen
|
-- (1) Primäre Dos-Partition löschen
-- (2) Erweiterte Dos-Partition löschen
-- (3) Logisches Dos-Laufwerk in der erweiterten Dos-Partition löschen
-- (4) Nicht-Dos-Partition löschen

(4) Partitionierungsdaten anzeigen
(5) Aktuelle Festplatte wechseln (nur bei der Verwendung mehrerer Festplatten)


Bevor man Festplatte zu partitionieren beginnt, sollten vorher definierte Partitionen
gelöscht werden. Hier wählt man zuerst den Menupunkt 4 (Partitionierungsdaten anzeigen)
gefolgt von dem Menpunkt 3 (Partition oder logisches Dos-Laufwerk löschen) und löscht
die vorhandenen Partitionen. Es ist darauf zu achten, daß erst die
"Nicht-Dos-Partition", dann das "Logisches Dos-Laufwerk", gefolgt von
der "Erweiterten"- und "Primären Dos-Partition" gelöscht werden.

Wenn das erledigt ist, kann man mit dem Menupunkt 1 (Dos-Partition oder logisches
Dos-Laufwerk erstellen) fortfahren.
Es gibt nun mehrere Möglichkeiten, wie man vorzugehen hat. Entscheidend ist, ob man
eine oder mehrere Partitionen erstellen möchte.


Festplatte in einer Partition:
Wenn man die Festplatte komplett in einer Partition nutzen möchte,
wählt man im Hauptmenu den Menupunkt 1 (Dos-Partition oder logisches Dos-Laufwerk
erstellen). Danach wählt man die Unteroption 1 (Primäre Dos-Partition erstellen)
und bestätigt, daß "der größtmöglich zur Verfügung stehende Speicherplatz verwendet
werden soll".
Daraufhin legt man diese erstellte Primäre Dos-Partition in dem
Menupunkt 2 als "Aktive" fest (es muß IMMER eine Partition als
Aktive festgelegt werden).


Festplatte in 2 und mehr Partitionen:
Wenn die Festplatte in zwei oder mehr Partitionen unterteilt werden soll,
verneint man, nachdem in dem Menupunkt 1 (Dos-Partition oder logisches Dos-Laufwerk
erstellen) die Unteroption 1 (Primäre Dos-Partition erstellen) gewählt hat, die
Abfrage, ob "der größtmöglich zur Verfügung stehende Speicherplatz verwendet
werden soll".

Daraufhin legt man die Größe der Primären Dos-Partition fest. Wenn das erledigt
ist, wählt man nach dem Menupunkt 1 die Unteroption 2 (Erweiterte Dos-Partition
erstellen). Dort gibt man den restlichen Festplattenspeicher an.
Jetzt wurde IN der Primären Dos-Partition eine Erweiterte Dos-Partition
erstellen, in der man, je nach Wunsch, so viele Logische Dos-Partitionen erstellen
kann, wie es einem beliebt.

Wenn man nun eine Dritte Partition erstellen möchte, wählt man nach dem
Menupunkt 1 die Unteroption 3 (Logisches Dos-Laufwerk in der erweiterten
Dos-Partition erstellen) aus. Hier gibt man jetzt die größe der
restlichen Partitionen an. Diese werden direkt IN der Erweiterten
Dos-Partition erstellt.
Ist das erledigst, muß man die Primäre Dos-Partition nur noch mit dem
Menupunkt 2 (Aktive Partition festlegen), als "Aktive" festlegen.




Zur Veranschaulichung:

Zuerst wird eine Primäre Dos-Partition erstellt. In dieser wird eine
Erweiterte Dos-Partition erstellt, in welcher wiederum alle anderen
Logischen Dos-Partitionen erstellt werden.

Die Primäre Dos-Partition muß immer als Aktive definiert werden.

Wenn zwei oder mehr Festplatten vorhanden sind, werden diese nach genau dem gleichen
Verfahren partitioniert. Allerdings ist hier darauf zu achten, daß nur die
Primäre Dos-Partition als Aktive festgelegt wird, von welcher Festplatte (Master)
auch gebootet wird. Die anderen Primären Dos-Partitionen in den anderen
Festplatten (Slave), brauchen nicht als Aktive definiert zu werden.


FESTPLATTE 1:

[PRIMÄRE DOS-PARTITION] [AKTIVE]
|
|
-- [ERWEITERTE DOS-PARTITION]
|
|
-- [LOGISCHE DOS-PARTITION 1]
-- [LOGISCHE DOS-PARTITION 2]
-- [LOGISCHE DOS-PARTITION 3]
-- usw.


FESTPLATTE 2:

[PRIMÄRE DOS-PARTITION] [AKTIVE]
|
|
-- [ERWEITERTE DOS-PARTITION]
|
|
-- [LOGISCHE DOS-PARTITION 1]
-- [LOGISCHE DOS-PARTITION 2]
-- [LOGISCHE DOS-PARTITION 3]
-- usw.



bye TheEvilOne
 
FDISK(8) Linux Programmer's Manual FDISK(8)



NAME
fdisk - Partition table manipulator for Linux

SYNOPSIS
fdisk [-u] [-b sectorsize]device

fdisk -l [-u] [-b sectorsize] [device ...]

fdisk -s partition ...

fdisk -v

DESCRIPTION
Hard disks can be divided into one or more logical disks
called partitions. This division is described in the par_
tition table found in sector 0 of the disk.

In the BSD world one talks about `disk slices' and a
`disklabel'.

Linux needs at least one partition, namely for its root
file system. It can use swap files and/or swap parti
tions, but the latter are more efficient. So, usually one
will want a second Linux partition dedicated as swap par
tition. On Intel compatible hardware, the BIOS that boots
the system can often only access the first 1024 cylinders
of the disk. For this reason people with large disks
often create a third partition, just a few MB large, typi
cally mounted on /boot, to store the kernel image and a
few auxiliary files needed at boot time, so as to make
sure that this stuff is accessible to the BIOS. There may
be reasons of security, ease of administration and backup,
or testing, to use more than the minimum number of parti
tions.

fdisk (in the first form of invocation) is a menu driven
program for creation and manipulation of partition tables.
It understands DOS type partition tables and BSD or SUN
type disklabels.

The device is usually one of the following:
/dev/hda
/dev/hdb
/dev/sda
/dev/sdb
(/dev/hd[a-h] for IDE disks, /dev/sd[a-p] for SCSI disks,
/dev/ed[a-d] for ESDI disks, /dev/xd[ab] for XT disks). A
device name refers to the entire disk.

The partition is a device name followed by a partition
number. For example, /dev/hda1 is the first partition on
the first IDE hard disk in the system. IDE disks can have
up to 63 partitions, SCSI disks up to 15. See also
/usr/src/linux/Documentation/devices.txt.

A BSD/SUN type disklabel can describe 8 partitions, the
third of which should be a `whole disk' partition. Do not
start a partition that actually uses its first sector
(like a swap partition) at cylinder 0, since that will
destroy the disklabel.

An IRIX/SGI type disklabel can describe 16 partitions, the
eleventh of which should be an entire `volume' partition,
while the ninth should be labeled `volume header'. The
volume header will also cover the partition table, i.e.,
it starts at block zero and extends by default over five
cylinders. The remaining space in the volume header may
be used by header directory entries. No partitions may
overlap with the volume header. Also do not change its
type and make some file system on it, since you will lose
the partition table. Use this type of label only when
working with Linux on IRIX/SGI machines or IRIX/SGI disks
under Linux.

A DOS type partition table can describe an unlimited num
ber of partitions. In sector 0 there is room for the
description of 4 partitions (called `primary'). One of
these may be an extended partition; this is a box holding
logical partitions, with descriptors found in a linked
list of sectors, each preceding the corresponding logical
partitions. The four primary partitions, present or not,
get numbers 1-4. Logical partitions start numbering from
5.

In a DOS type partition table the starting offset and the
size of each partition is stored in two ways: as an abso
lute number of sectors (given in 32 bits) and as a Cylin
ders/Heads/Sectors triple (given in 10+8+6 bits). The for
mer is OK - with 512-byte sectors this will work up to 2
TB. The latter has two different problems. First of all,
these C/H/S fields can be filled only when the number of
heads and the number of sectors per track are known. Sec
ondly, even if we know what these numbers should be, the
24 bits that are available do not suffice. DOS uses C/H/S
only, Windows uses both, Linux never uses C/H/S.

If possible, fdisk will obtain the disk geometry automati
cally. This is not necessarily the physical disk geometry
(indeed, modern disks do not really have anything like a
physical geometry, certainly not something that can be
described in simplistic Cylinders/Heads/Sectors form), but
is the disk geometry that MS-DOS uses for the partition
table.

Usually all goes well by default, and there are no prob
lems if Linux is the only system on the disk. However, if
the disk has to be shared with other operating systems, it
is often a good idea to let an fdisk from another operat
ing system make at least one partition. When Linux boots
it looks at the partition table, and tries to deduce what
(fake) geometry is required for good cooperation with
other systems.

Whenever a partition table is printed out, a consistency
check is performed on the partition table entries. This
check verifies that the physical and logical start and end
points are identical, and that the partition starts and
ends on a cylinder boundary (except for the first parti
tion).

Some versions of MS-DOS create a first partition which
does not begin on a cylinder boundary, but on sector 2 of
the first cylinder. Partitions beginning in cylinder 1
cannot begin on a cylinder boundary, but this is unlikely
to cause difficulty unless you have OS/2 on your machine.

A sync() and a BLKRRPART ioctl() (reread partition table
from disk) are performed before exiting when the partition
table has been updated. Long ago it used to be necessary
to reboot after the use of fdisk. I do not think this is
the case anymore - indeed, rebooting too quickly might
cause loss of not-yet-written data. Note that both the
kernel and the disk hardware may buffer data.


DOS 6.x WARNING
The DOS 6.x FORMAT command looks for some information in
the first sector of the data area of the partition, and
treats this information as more reliable than the informa
tion in the partition table. DOS FORMAT expects DOS FDISK
to clear the first 512 bytes of the data area of a parti
tion whenever a size change occurs. DOS FORMAT will look
at this extra information even if the /U flag is given --
we consider this a bug in DOS FORMAT and DOS FDISK.

The bottom line is that if you use cfdisk or fdisk to
change the size of a DOS partition table entry, then you
must also use dd to zero the first 512 bytes of that par
tition before using DOS FORMAT to format the partition.
For example, if you were using cfdisk to make a DOS parti
tion table entry for /dev/hda1, then (after exiting fdisk
or cfdisk and rebooting Linux so that the partition table
information is valid) you would use the command "dd
if=/dev/zero of=/dev/hda1 bs=512 count=1" to zero the
first 512 bytes of the partition.

BE EXTREMELY CAREFUL if you use the dd command, since a
small typo can make all of the data on your disk useless.

For best results, you should always use an OS-specific
partition table program. For example, you should make DOS
partitions with the DOS FDISK program and Linux partitions
with the Linux fdisk or Linux cfdisk program.


OPTIONS
-b sectorsize
Specify the sector size of the disk. Valid values
are 512, 1024, or 2048. (Recent kernels know the
sector size. Use this only on old kernels or to
override the kernel's ideas.)

-l List the partition tables for the specified devices
and then exit. If no devices are given, those men
tioned in /proc/partitions (if that exists) are
used.

-u When listing partition tables, give sizes in sec
tors instead of cylinders.

-s partition
The size of the partition (in blocks) is printed on
the standard output.

-v Print version number of fdisk program and exit.

BUGS
There are several *fdisk programs around. Each has its
problems and strengths. Try them in the order cfdisk,
fdisk, sfdisk. (Indeed, cfdisk is a beautiful program
that has strict requirements on the partition tables it
accepts, and produces high quality partition tables. Use
it if you can. fdisk is a buggy program that does fuzzy
things - usually it happens to produce reasonable results.
Its single advantage is that it has some support for BSD
disk labels and other non-DOS partition tables. Avoid it
if you can. sfdisk is for hackers only - the user inter
face is terrible, but it is more correct than fdisk and
more powerful than both fdisk and cfdisk. Moreover, it
can be used noninteractively.)

The IRIX/SGI type disklabel is currently not supported by
the kernel. Moreover, IRIX/SGI header directories are not
fully supported yet.

The option `dump partition table to file' is missing.

SEE ALSO
cfdisk(8), parted(8), sfdisk(8)



Linux 2.0 11 June 1998 FDISK(8)
 
Zurück
Oben