CH6640E (Kabel Deutschland) WLAN aktivieren

Wenn man in der Weboberfläche rumsurft wird immer von /xml/GlobalSettings.xml eine Datei geladen. Darin steht eine Variable ConfigDisableWIFI die auf 1 gesetzt ist. Wenn man den Request dorthin abfängt(z.b. mit Fiddler) und 0 anstatt 1 einträgt sieht man ein erweitertes Menü. Folgende URLs kann man dann sehen, man wird allerdings sofort ausgeloggt wenn man sie annavigiert:

/ipv6Config.html
/ipv6PortFiltering.html
/ipv6IDS.html
/ipv6Status.html

/wirelessBandMode.html

/RemoteManagement.html
 
Meldet man sich als Admin im Webinterface an und ändert dann im Cookie "userData" den Wert von "admin" auf "root" (mit dem Firefox Plugin 'Firebug') bekommt man neben den Standard-Menüpunkten, noch einige andere (die mit X gekennzeichneten). Wie aber auch bei den WLAN-Menüpunkten, kann man meisten dieser neuen Menüpunkte nicht ansurfen. Ansurfen kann man nur die mit # gekennzeichenten. Auch zeigt nun "Cable Modem" -> "Configuration" interessante Informationen!

Code:
Cable Modem
    Status
    Signals
    Logs (X)
    Addresses (X)
    Configuration (#)
    Provisioning (X)

Gateway
    Basic
        Setup
        DHCP
        Lan Users
    IPV6
        IP Filtering
        MAC Forwarding
        Intrusion Detection
        Status
    Management
        Change password

Telephone
    Status
    Call (X)
    Logs (X)
    Call History (X)
    Provisioning (X#)
    Configuration (X#)

Help
    Cable Modem
    Telephone
Auf der Platine befindet sich ein 4 poliger Stecker/Header (J4, nicht bestückt, im Bild unten von mir falsch beschriftet). Dieser ist ein sehr gesprächiger serieller Port. Empfangen kann man da während dem booten sehr viel. Man erfährt viel über die Hardware. Mehr Infos dazu gibt es wenn ich meinen bestellten USB-Seriell-Wandler erhalten habe, da ich mit meinem derzeitigen Aufbau nicht komfortabel mit dem CBN in beiden Richtungen kommunizieren kann.

1389907099x1599859314.jpg
1389907150x1599859314.jpg
 
Zuletzt bearbeitet:
Falls es jemanden interessiert, was bei J4 (serieller Port auf der Platine) nach einem Reboot über das Webinterface mit komplettem Boot gesendet wird, könnt ihr das hier nachlesen. Auf Eingaben reagiert das CBN leider nicht.
Vielleicht steht das "NOSH" im Namen der Firmwareversion für "no sh", also "keine shell"?

(persönliche Daten habe ich zensiert)
Code:
CM reboot reason is already written to the file -- dont write

The system is going down NOW!
sigterm_prog=0;calling vp880_restart
pcd: Terminating PCD, rebooting system...
 TI Logger: Terminating...
writing to ipc socket: No such file or directory
error, Received SIGTERM
error, Received SIGTERM
info, udhcpc_get_stats
Jan/18/2014 17:43:06: client6_signal: received a signal (15)
Jan/43:06 Server Critical  Signal received. Shutting down.
43:06 Server Warning   Service SHUTDOWN.
43:06 Server Debug     Failed to read sockets (select() returne*** Reset Tuner #0 ***
*** Reset Tuner #1 ***
failed to send close agent command to SNMP agent!!!
Select failed: : Interrupted system call
Jan/18/2014 17:43:06: remove_siteprefix: remove a site prefix xxxxxxxxxxxxxxxxx
Jan/18/2014 17:43:06: dhcp6_reset_timer: reset a timer on lbr0, state=INIT, timeo=0, retrans=897
Jan/18/2014 17:43:06: release_ia: release an IA: NA-
Jan/18/2014 17:43:06: dhcp6_reset_timer: reset a timer on lbr0, state=RELEASE, timeo=0, retrans=1002
Jan/18/2014 17:43:06: client6_send: a new XID (b1c9da) is generated
Jan/18/2014 17:43:06: copy_option: set client ID (len 10)
Jan/18/2014 17:43:06: copy_option: set server ID (len 14)
Jan/18/2014 17:43:06: copyout_option: set IA address
Jan/18/2014 17:43:06: copyout_option: set identity association
Jan/18/2014 17:43:06: copy_option: set elapsed time (len 2)
Jan/18/2014 17:43:06: client6_send: send release to ff02::1:2
Jan/18/2014 17:43:06: remove_ia: remove an IA: NA-xxxxxxxxxxxxx
Jan/18/2014 17:43:06: remove_addr: remove an address xxxxxxxxxxxxxxxxxx
Jan/18/2014 17:43:06: ifaddrconf: remove an address xxxxxxxxxxxxxxxxxx/128 on lbr0
Jan/18/2014 17:43:06: dhcp6_reset_timer: reset a timer on lbr0, state=INIT, timeo=0, retrans=31
Jan/18/2014 17:43:06: dhcp6_remove_event: removing an event on lbr0, state=INIT
Jan/18/2014 17:43:06: dhcp6_remove_event: removing an event on lbr0, state=INIT
mxp_ev_wait for task 1 waken up by unexpected signal
mxp_ev_wait for task 13 waken up by unexpected signal
mxp_ev_wait for task 15 waken up by unexpected signal
mxp_q_wait for queueId 35 waken up by unexpected signal
mxp_ev_wait for task 8 waken up by unexpected signal
mxp_ev_wait for task 10 waken up by unexpected signal
mxp_ev_wait for task 12 waken up by unexpected signal
mxp_ev_wait for task 7 waken up by unexpected signal
mxp_ev_wait for task 14 waken up by unexpected signal
mxp_ev_wait for task 4 waken up by unexpected signal
mxp_ev_wait for task 9 waken up by unexpected signal
mxp_ev_wait for task 11 waken up by unexpected signal
mxp_ev_wait for task 18 waken up by unexpected signal
mxp_q_wait for queueId 1 waken up by unexpected signal

Sent SIGKILL to all processes

Requesting system reboot

**************TIPuma5 send system reboot command to wifi*****************
Restarting system.


U-Boot 1.2.0 (Aug 10 2012 - 20:37:39)
PSPU-Boot(BBU) 1.0.12.19m1-CBN03

DRAM:  128 MB
Spansion S25FL129P flash found
Spansion S25FL129P flash found
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Start Memory testing
Memory testing OK
*** ACTIMAGE = 2, will try to boot UBFI2 stored @0x4c000000
## Executing script at 4c000000
============== Running script =========
*** Running from UBFI2 partition @0x4c000000
Load address = 0x4c00236c (0x236c)
Kernel address = 0x4c0023b8 (0x23b8)
kernel size = 0x154c48
Root FS address = 0x4c157000 (0x157000)
Root FS size = 0x8d9800
Additional FS =
NVRAM offset = 0x40000
NVRAM size = 0x50000
NVRAM1 offset = 0x90000
NVRAM1 size = 0x20000
*** UBFI2 bootscript executed successfully.
Start booting...
## Booting image at 4c00236c ...
   Image Name:   Multi Image File
   Image Type:   ARM Linux Multi-File Image (uncompressed)
   Data Size:    10675284 Bytes = 10.2 MB
   Load Address: 80a00000
   Entry Point:  80a00000
   Contents:
   Image 0:  1395784 Bytes =  1.3 MB
   Image 1:  9279488 Bytes =  8.8 MB
   Verifying Checksum ... OK
OK

Starting kernel ...

Starting LZMA Uncompression Algorithm.
Compressed file is LZMA format.
Linux version 2.6.39.3 (T105011@vcs) (gcc version 4.6.1 (Buildroot 2011.08) ) #1 PREEMPT Wed Sep 11 20:18:03 CST 2013
CPU: ARMv6-compatible processor [410fb764] revision 4 (ARMv7), cr=00c538ff
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: puma5
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
Reserved 2048k DSP memory starting from Physical 0x87e00000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32004
Kernel command line: root=/dev/mtdblock8 mtdparts=spansion:0x20000(U-Boot)ro,0x10000(env1),0x10000(env2),0x50000@0x40000(nvram),0x20000@0x90000(nvram1),0xf50000@0xb0000(UBFI1);spansion1:0xf50000@0(UBFI2),0x154c48@0x23b8(Kernel)ro,0x8d9800(RootFileSystem)ro console=ttyS0,115200n8 ethaddr0=00.50.f1.10.00.01 usbhostaddr= boardtype=tnetc552 clock_25_mhz=OFF eth0_mdio_phy_addr= ext_switch_reset_gpio= threadirqs
 CPGMAC PHY MDIO ADDRESS []
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126MB = 126MB total
Memory: 123672k/123672k available, 5352k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0x88000000 - 0x90000000   ( 128 MB)
    lowmem  : 0x80000000 - 0x87e00000   ( 126 MB)
    modules : 0x7f000000 - 0x80000000   (  16 MB)
      .init : 0x80018000 - 0x80037000   ( 124 kB)
      .text : 0x80037000 - 0x803ca000   (3660 kB)
      .data : 0x803ca000 - 0x803e2ee0   ( 100 kB)
Preemptable hierarchical RCU implementation.
    RCU-based detection of stalled CPUs is disabled.
    Verbose stalled-CPUs detection is disabled.
NR_IRQS:150
Interrupt controller revision : 4e822100
Power & Sleep Controller @ 0xd8621000 Initialized [id-0x44822905]
USB PHY POR Bypass enabled
Board type: tnetc552
Initialized Peripheral Port Remap Register to base : 0x50000000
Puma5 Timer0 initialized
console [ttyS0] enabled
Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
hw perfevents: enabled with v6 PMU driver, 3 counters available
NET: Registered protocol family 16
hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
 PAL_cppi4Init : domain is 0, cfg ptr is 0x803D09EC 
 PAL_cppi4Init : Object Address is 0x803E3174 
 PAL_cppi4Init : Before MEM Test 
 PAL_cppi4Init : Before QMGR Init 
 PAL_cppi4Init : QMGR [0] Init ... 
PAL_cppi4Init : There is a room for 1315 more descriptors
Off chip memory allocated: 349120
QMgr Init: buffer after alignment: 87880000
 PAL_cppi4Init : QMGR [1] Init ... 
 PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000 
 PAL_cppi4Init : Object Address is 0x803E3174 
avalanche_ppd_init: PP system  initialized successfully.
 PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000 
 PAL_cppi4Init : Object Address is 0x803E3174 
PAL_cppi4BufPoolDirectInit : Pool[10] is at 0x87900000 of 0x00040000 size
PAL_cppi4BufPoolDirectInit : Pool[11] is at 0x87980000 of 0x00080000 size
PAL_cppi4BufPoolDirectInit : Pool[13] is at 0x87860000 of 0x00020000 size
PAL_cppi4BufPoolDirectInit : Pool[ 6] is at 0x87940000 of 0x00020000 size
PAL_cppi4BufPoolDirectInit : Pool[ 7] is at 0x87A00000 of 0x00080000 size
PAL_cppi4BufPoolDirectInit : Pool[ 0] is at 0x87A80000 of 0x00080000 size
PAL_cppi4BufPoolDirectInit : Pool[ 1] is at 0x87B00000 of 0x00080000 size
PAL_cppi4BufPoolDirectInit : Pool[ 4] is at 0x87B80000 of 0x00080000 size
PAL_cppi4BufPoolDirectInit : Pool[ 5] is at 0x87850000 of 0x00010000 size
PAL_cppi4BufPoolDirectInit : Pool[12] is at 0x87000000 of 0x00080000 size
PAL_cppi4BufPoolDirectInit : Pool[ 2] is at 0x87080000 of 0x00080000 size
PAL_cppi4BufPoolDirectInit : Pool[ 8] is at 0x87960000 of 0x00010000 size
avalanche_ppd_init(933):return code 0x00
bio: create slab <bio-0> at 0
SCSI subsystem initialized
HIL Core: Profile intrusive has been Loaded.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.30 [Flags: R/W].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.16)
msgmni has been set to 241
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x8610f03 (irq = 8) is a TI 16550A
serial8250: ttyS1 at MMIO 0x8610e03 (irq = 7) is a TI 16550A
TI LED driver initialized [major=253]
loop: module loaded
Serial Flash [Bus:0 CS:0] : s25fl128p 16384KB, 256 sectors each  64KB 
6 cmdlinepart partitions found on MTD device spansion
partitions[0] = {.name = U-Boot, .offset = 0x00000000,.size = 0x00020000 (128K) }
partitions[1] = {.name = env1, .offset = 0x00020000,.size = 0x00010000 (64K) }
partitions[2] = {.name = env2, .offset = 0x00030000,.size = 0x00010000 (64K) }
partitions[3] = {.name = nvram, .offset = 0x00040000,.size = 0x00050000 (320K) }
partitions[4] = {.name = nvram1, .offset = 0x00090000,.size = 0x00020000 (128K) }
partitions[5] = {.name = UBFI1, .offset = 0x000b0000,.size = 0x00f50000 (15680K) }
Creating 6 MTD partitions on "spansion":
0x000000000000-0x000000020000 : "U-Boot"
0x000000020000-0x000000030000 : "env1"
0x000000030000-0x000000040000 : "env2"
0x000000040000-0x000000090000 : "nvram"
0x000000090000-0x0000000b0000 : "nvram1"
0x0000000b0000-0x000001000000 : "UBFI1"
Serial Flash [Bus:0 CS:1] : s25fl128p 16384KB, 256 sectors each  64KB 
3 cmdlinepart partitions found on MTD device spansion1
partitions[0] = {.name = UBFI2, .offset = 0x00000000,.size = 0x00f50000 (15680K) }
partitions[1] = {.name = Kernel, .offset = 0x000023b8,.size = 0x00154c48 (1363K) }
partitions[2] = {.name = RootFileSystem, .offset = 0x00157000,.size = 0x008d9800 (9062K) }
Creating 3 MTD partitions on "spansion1":
0x000000000000-0x000000f50000 : "UBFI2"
0x0000000023b8-0x000000157000 : "Kernel"
0x000000157000-0x000000a30800 : "RootFileSystem"
(null): AVALANCHE SPI Controller driver at 0xd8612500           (irq = 0)
(null): TI Codec SPI Controller driver at 0xd86040c8           (irq = 0)
ftmac100: Loading version 0.2 ...
dm9000 Ethernet Driver, V1.31
Loading cpgmac driver for puma5 
   Rudek 00000002 
 PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000 
 PAL_cppi4Init : Object Address is 0x803E3174 
TI CPGMAC_F Linux DDA version 0.1 - CPGMAC_F DDC version 0.2
Cpmac: Installed 1 instances.
i2c /dev entries driver
watchdog: TI Avalanche Watchdog Timer: timer margin 42 sec
cpuidle: using governor ladder
IPv4 over IPv4 tunneling driver
GRE over IPv4 demultiplexor driver
GRE over IPv4 tunneling driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
L2TP core driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFP support v0.3: not present
VFS: Mounted root (squashfs filesystem) readonly on device 31:8.
Freeing init memory: 124K

init started: BusyBox v1.19.2 (2013-09-11 20:20:18 CST)
************************************
rcS Start
************************************
hwclock: can't open '/dev/misc/rtc': No such file or directory
Mount nvram on /dev/mtdblock3


========================================================
TI CH6640 release 3.5.0.12
Build date: Wednesday, September 11 2013, 20:45:54
Copyright (c) 2011, Intel Corporation.
========================================================


EMIF Controller and DDR PHY in Sync
Using DOCSIS Initialization process parameters: -us_channels 4
Using DOCSIS MAC Manager parameters: -x -m
pcd: (191): Starting TI Process Control Daemon.Please press Enter to activate this console. pcd: (192): Loaded 98 rules.
pcd: Initialization complete.
pcd: (192): Starting process /usr/sbin/watchdog_rt (Rule SYSTEM_WATCHDOG).
pcd: (192): Starting process /usr/sbin/logger (Rule SYSTEM_LOGGER).
pcd: (192): Rule SYSTEM_WATCHDOG: Success (Process /usr/sbin/watchdog_rt (195)).
TI Watchdog-RT daemon started <kick interval = 10 seconds>
TOKEN ACCESS LIFE SPAN restored from nvram
TOKEN ACCESS SEQUENCE NUMBER restored from nvram
TOKEN ACCESS USAGE COUNT restored from nvram
TOKEN ACCESS HASH CALCULATED restored from nvram
TOKEN ACCESS INSTALLED restored from nvram
TOKEN ACCESS PUBLIC KEY restored from nvram
TOKEN ACCESS PUBLIC KEY USER NAME restored from nvram
TOKEN ACCESS DIGEST VALUE restored from nvram
Restoring motorola Token Access NVRAM DB from NVRAM ... SUCCESS
TI Logger: Init complete
pcd: (192): Rule SYSTEM_LOGGER: Success (Process /usr/sbin/logger (196)).
pcd: (192): Starting process /usr/sbin/gptimer (Rule SYSTEM_GPTIMER).
pcd: (192): Starting process /usr/sbin/gim (Rule SYSTEM_GIM).
pcd: (192): Rule SYSTEM_GPTIMER: Success (Process /usr/sbin/gptimer (197)).
pcd: (192): Rule SYSTEM_GIM: Success (Process /usr/sbin/gim (198)).
pcd: (192): Rule SYSTEM_LASTRULE: Success.
pcd: (192): Starting process /bin/sh (Rule BBU_INITDRV).
pcd: (192): Rule PREDOCSIS_LASTRULE: Success.
BBU Kernel module - installing
BbuIsRev2: rev 1
BBU Kernel module installed - 0
pcd: (192): Rule BBU_INITDRV: Success (Process /bin/sh (200)).
pcd: (192): Starting process /usr/sbin/bbusm (Rule BBU_SM).
pcd: (192): Rule BBU_SM: Success (Process /usr/sbin/bbusm (207)).
pcd: (192): Starting process /usr/sbin/psm (Rule MOTOBBU_PSM).
pcd: (192): Rule MOTOBBU_PSM: Success (Process /usr/sbin/psm (209)).
pcd: (192): Starting process /bin/sh (Rule BBU_DLMRMMOD).
pcd: (192): Rule BBU_LASTRULE: Success.
pcd: (192): Starting process echo (Rule DOCSIS_APPRUN).
pcd: (192): Rule DOCSIS_APPRUN: Success (Process echo (211)).
pcd: (192): Starting process /usr/sbin/docsis_init_once (Rule DOCSIS_INITONCE).
jffs2: Too few erase blocks (2)
mount: mounting /dev/mtdblock4 on /nvram1 failed: Invalid argument
umount: can't forcibly umount /nvram1: Invalid argument
/bin/sh: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_time_wait: nonexistent directory
/bin/sh: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout: nonexistent directory
/bin/sh: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_icmp_timeout: nonexistent directory
jffs2: Too few erase blocks (2)
mount: mounting /dev/mtdblock4 on /nvram1 failed: Invalid argument
umount: can't forcibly umount /nvram1: Invalid argument

CBN:  Decrypt private key start

CBN: Decrypt private key success!! 
echo net.ipv4.netfilter.ip_conntrack_tcp_timeout_time_wait=120 >> /etc/sysctl.conf
CBN: echo net.ipv4.netfilter.ip_conntrack_tcp_timeout_time_wait=120 >> /etc/sysctl.conf
echo net.ipv4.netfilter.ip_conntrack_udp_timeout=30 >> /etc/sysctl.conf
CBN: echo net.ipv4.netfilter.ip_conntrack_udp_timeout=30 >> /etc/sysctl.conf
echo net.ipv4.netfilter.ip_conntrack_icmp_timeout=4 >> /etc/sysctl.conf
CBN: echo net.ipv4.netfilter.ip_conntrack_icmp_timeout=4 >> /etc/sysctl.conf
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
pcd: (192): Rule DOCSIS_INITONCE: Success (Process /usr/sbin/docsis_init_once (212)).
pcd: (192): Starting process /usr/sbin/ti_webserver (Rule MOTO_WEB_HFC).
pcd: (192): Starting process /usr/sbin/ti_webserver (Rule MOTO_WEB_CPE).
pcd: (192): Rule MOTO_WEB_CPE: Success (Process /usr/sbin/ti_webserver (238)).
pcd: (192): Rule MOTO_WEB_HFC: Success (Process /usr/sbin/ti_webserver (237)).
pcd: (192): Starting process insmod (Rule DOCSIS_HALVLYNQ).
pcd: (192): Starting process /usr/sbin/cm_status (Rule DOCSIS_CMSTATUS).
pcd: (192): Rule DOCSIS_CMSTATUS: Success (Process /usr/sbin/cm_status (240)).
pcd: (192): Rule DOCSIS_HALVLYNQ: Success (Process insmod (239)).
pcd: (192): Starting process insmod (Rule DOCSIS_SOCIFDRV).
 PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000 
 PAL_cppi4Init : Object Address is 0x803E3174 
RX Init CPPI: open free descriptor queue
RX Init CPPI: allocate descriptors
init_cppi_rx: Allocate descriptors to the embedded free queues
RX Init CPPI: Fill free discriptor queue
RX Init CPPI: Set DMA channel
init_cppi_rx: Call PAL_cppi4RxChOpen channel=12, REF_CNT=1 BUF COUNT=512
RX Init CPPI: Init accumulator
RX Init RX CPPI pass
TX Init CPPI: open free descriptor queue
TX Init CPPI: allocate descriptors
init_cppi_tx: Allocate descriptors to the embedded free queues
TX Init CPPI: Fill free discriptor queue
TX Init CPPI: Create CPGMAC TX handler
TX Init CPPI: open mpeg TX channel
TX Init CPPI pass
WQ Init CPPI: open queue descriptor queue
WQ Init pass
MPEG driver initialization complete.
pcd: (192): Rule DOCSIS_SOCIFDRV: Success (Process insmod (242)).
pcd: (192): Starting process mknod (Rule DOCSIS_MKNODSOCIFDRV).
pcd: (192): Starting process insmod (Rule DOCSIS_BRIDGE).
pcd: (192): Rule DOCSIS_MKNODSOCIFDRV: Success (Process mknod (245)).
pcd: (192): Starting process insmod (Rule DOCSIS_MNG).
 PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000 
 PAL_cppi4Init : Object Address is 0x803E3174 
 Entered HAL_DocsisCppiInit 
 PAL_cppi4Init : domain is 1, cfg ptr is 0x7F0555A8 
 PAL_cppi4Init : Object Address is 0x803E4A54 
 PAL_cppi4Init : Before MEM Test 
 PAL_cppi4Init : Before QMGR Init 
pcd: (192): Rule DOCSIS_BRIDGE: Success (Process insmod (246)).
pcd: (192): Starting process insmod (Rule DOCSIS_CNI).
 PAL_cppi4Init : QMGR [0] Init ... 
 PAL_cppi4Init : QMGR [1] Init ... 
Off chip memory allocated: 32768
QMgr Init: buffer after alignment: 86da0000
PAL_cppi4BufPoolDirectInit : Pool[ 0] is at 0x01040000 of 0x00008000 size
pcd: (192): Rule DOCSIS_MNG: Success (Process insmod (247)).
pcd: (192): Starting process mknod (Rule DOCSIS_MKNODMNG).
pcd: (192): Starting process insmod (Rule DOCSIS_KINTR).
pcd: (192): Rule DOCSIS_MKNODMNG: Success (Process mknod (259)).
 PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000 
 PAL_cppi4Init : Object Address is 0x803E3174 
pcd: (192): Rule DOCSIS_CNI: Success (Process insmod (250)).
pcd: (192): Rule DOCSIS_KINTR: Success (Process insmod (260)).
pcd: (192): Starting process insmod (Rule DOCSIS_FILTERCLASS).
pcd: (192): Starting process /usr/sbin/hal_event_mbox (Rule DOCSIS_HALEVENTMBOX).
pcd: (192): Starting process /usr/sbin/hal_cmd_mbox (Rule DOCSIS_HALCMDMBOX).
pcd: (192): Rule DOCSIS_FILTERCLASS: Success (Process insmod (278)).
pcd: (192): Starting process /bin/sh (Rule DOCSIS_FCDEV).
pcd: (192): Rule DOCSIS_FCDEV: Success (Process /bin/sh (288)).
pcd: (192): Starting process /usr/sbin/dbridge_init (Rule DOCSIS_DBRIDGEINIT).
Dbridge Init SUCSESS
Autoconfiguration disabled for lbr0
Could not find eth0 with MAC <ETH MAC> in DbrDB Devices
pcd: (192): Rule DOCSIS_HALCMDMBOX: Success (Process /usr/sbin/hal_cmd_mbox (285)).
pcd: (192): Rule DOCSIS_HALEVENTMBOX: Success (Process /usr/sbin/hal_event_mbox (284)).
pcd: (192): Starting process /usr/sbin/mlx (Rule DOCSIS_MLX).
pcd: (192): Rule DOCSIS_MLX: Success (Process /usr/sbin/mlx (301)).
pcd: (192): Starting process /usr/sbin/hal_tuner_mgr (Rule DOCSIS_HALTUNERMGR).
Autoconfiguration disabled for lan0
Autoconfiguration disabled for wan0
Autoconfiguration disabled for cni0
Autoconfiguration disabled for br0


dbridge_init: Gateway Mode

************************************
Config_gw.sh start
************************************
pcd: (192): Rule DOCSIS_HALTUNERMGR: Success (Process /usr/sbin/hal_tuner_mgr (310)).
Unloading the BBU DLM
BBU module is down!
pcd: (192): Rule BBU_DLMRMMOD: Success (Process /bin/sh (210)).
Error: PACM ProvDB retrieve Access failed
Error: PACM ProvDB retrieve Access failed
pcd: (192): Error: Process /usr/sbin/ti_webserver (237) exited unexpectedly (Rule MOTO_WEB_HFC).
pcd: (192): Error: Rule MOTO_WEB_HFC failed.
Terminated
syslogd: /etc/syslog.conf: No such file or directory
pcd: (192): Error: Process /usr/sbin/ti_webserver (238) exited unexpectedly (Rule MOTO_WEB_CPE).
pcd: (192): Error: Rule MOTO_WEB_CPE failed.
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
Motorola lo entered
Motorola lbr0 entered
udhcpc (v1.19.2) started
There is no such command.
Error occured during reading below line.
timers basic

Loading defaults
NAT Table update all sessions flushed
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
NAT Table update all sessions flushed
iptables: Bad rule (does a matching rule exist in that chain?).
NAT Table update all sessions flushed
iptables: No chain/target/match by that name.
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
iptables: No chain/target/match by that name.
NAT Table update all sessions flushed
iptables: No chain/target/match by that name.
NAT Table update all sessions flushed
iptables: No chain/target/match by that name.
uci: Entry not found
iptables: No chain/target/match by that name.
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
Loading synflood protection
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
iptables: No chain/target/match by that name.
NAT Table update all sessions flushed
iptables: No chain/target/match by that name.
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
iptables: No chain/target/match by that name.
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
iptables: No chain/target/match by that name.
NAT Table update all sessions flushed
Loading blockIpFrag protection
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
Loading ipsec pass through
uci: Entry not found
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
Loading ipsec pass through
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
iptables: Chain already exists.
NAT Table update all sessions flushed
Loading pptp pass through
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
iptables: Chain already exists.
NAT Table update all sessions flushed
Adding custom chains
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
Loading zones
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
<4>NAT Table update all sessions flushed
iptables: Chain already exists.
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
iptables: Chain already exists.
iptables: Chain already exists.
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
Loading IPv6 defaults
Loading rules
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
Loading forwarding
NAT Table update all sessions flushed
NAT Table update all sessions flushed
Loading includes
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
iptables: Bad rule (does a matching rule exist in that chain?).
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
uci: Entry not found
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
iptables: No chain/target/match by that name.
NAT Table update all sessions flushed
iptables: No chain/target/match by that name.
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
Loading ipv6 synflood chain
Loading IPv6 blockIpFrag protection
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
iptables: Chain already exists.
NAT Table update all sessions flushed
NAT Table update all sessions flushed
No lease, forking to background
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
uci: Entry not found
killall: udhcpd: no process killed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
/etc/scripts/config_gw.sh: line 65: /usr/sbin/cbn_update_dlna: not found
************************************
Config_gw.sh end
************************************
pcd: (192): Rule DOCSIS_DBRIDGEINIT: Success (Process /usr/sbin/dbridge_init (294)).
pcd: (192): Starting process /bin/sh (Rule DOCSIS_DBRIDGEMDFINIT).
pcd: (192): Starting process /bin/sh (Rule DOCSIS_DBRIDGEL2VPNDSI).
pcd: (192): Rule DOCSIS_DBRIDGEMDFINIT: Success (Process /bin/sh (1639)).
pcd: (192): Starting process insmod (Rule DOCSIS_PP).
pcd: (192): Rule DOCSIS_DBRIDGEL2VPNDSI: Success (Process /bin/sh (1640)).
pcd: (192): Rule DOCSIS_PP: Success (Process insmod (1648)).
pcd: (192): Starting process /bin/sh (Rule DOCSIS_PPDEV).
pcd: (192): Starting process /usr/sbin/ledd (Rule DOCSIS_LED).
pcd: (192): Rule DOCSIS_HALREADY: Success.
pcd: (192): Rule DOCSIS_LED: Success (Process /usr/sbin/ledd (1655)).
pcd: (192): Starting process /usr/sbin/mptint (Rule DOCSIS_MPT_INT).
pcd: (192): Starting process /usr/sbin/cbn_natbypass_mac (Rule CBN_NATMACPASSTHROU).
pcd: (192): Starting process /usr/sbin/limWlanInit (Rule CBN_LIMINIT).
pcd: (192): Starting process /usr/sbin/snmp_agent_cm (Rule DOCSIS_SNMPAGENT).
pcd: (192): Starting process /usr/sbin/qos_dsx_sm (Rule DOCSIS_QOSDSXSM).
pcd: (192): Rule CBN_LIMINIT: Success (Process /usr/sbin/limWlanInit (1658)).
pcd: (192): Rule CBN_NATMACPASSTHROU: Success (Process /usr/sbin/cbn_natbypass_mac (1657)).
pcd: (192): Rule DOCSIS_MPT_INT: Success (Process /usr/sbin/mptint (1656)).
pcd: (192): Starting process /usr/sbin/dispatcher (Rule DOCSIS_DISPATCHER).
pcd: (192): Starting process /usr/sbin/bpi_auth (Rule DOCSIS_BPIAUTH).
pcd: (192): Rule DOCSIS_PPDEV: Success (Process /bin/sh (1652)).
netlink_open: initialized fd 6
pcd: (192): Rule DOCSIS_DISPATCHER: Success (Process /usr/sbin/dispatcher (1661)).
pcd: (192): Starting process /usr/sbin/docsis_mac_driver (Rule DOCSIS_MACDRIVER).
limWlanInit process exit successfully.
retrieve CbnGwDbEntries1 success
retrieve CBN_VLAN_DB_RetrieveAccess success
retrieve CBN_GRETUNNEL_DB_RetrieveAccess success
CBN:ebtables -t broute -F BROUTING
pcd: (192): Rule DOCSIS_BPIAUTH: Success (Process /usr/sbin/bpi_auth (1662)).
pcd: (192): Starting process /usr/sbin/bpi_tek (Rule DOCSIS_BPITEK).
pcd: (192): Starting process /usr/sbin/bpi_sa_map (Rule DOCSIS_BPISAMAP).
pcd: (192): Rule DOCSIS_QOSDSXSM: Success (Process /usr/sbin/qos_dsx_sm (1660)).
pcd: (192): Rule DOCSIS_BPISAMAP: Success (Process /usr/sbin/bpi_sa_map (1681)).
pcd: (192): Rule DOCSIS_BPITEK: Success (Process /usr/sbin/bpi_tek (1680)).
pcd: (192): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR8).
pcd: (192): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR7).
pcd: (192): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR6).
pcd: (192): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR5).
pcd: (192): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR4).
pcd: (192): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR3).
pcd: (192): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR2).
pcd: (192): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR1).
pcd: (192): Rule DOCSIS_DSMNGR5: Success (Process /usr/sbin/downstream_manager (1685)).
pcd: (192): Rule DOCSIS_DSMNGR1: Success (Process /usr/sbin/downstream_manager (1689)).
pcd: (192): Rule DOCSIS_DSMNGR2: Success (Process /usr/sbin/downstream_manager (1688)).
pcd: (192): Rule DOCSIS_DSMNGR3: Success (Process /usr/sbin/downstream_manager (1687)).
pcd: (192): Rule DOCSIS_DSMNGR7: Success (Process /usr/sbin/downstream_manager (1683)).
pcd: (192): Rule DOCSIS_DSMNGR8: Success (Process /usr/sbin/downstream_manager (1682)).
pcd: (192): Rule DOCSIS_DSMNGR6: Success (Process /usr/sbin/downstream_manager (1684)).
pcd: (192): Rule DOCSIS_DSMNGR4: Success (Process /usr/sbin/downstream_manager (1686)).
rm: can't remove '/var/tmp/vendorSwServer': No such file or directory
rm: can't remove '/var/tmp/vendorSwFilename': No such file or directory
rm: can't remove '/var/tmp/vendorCVC': No such file or directory
SNMPA_CreateSocketEntry : type 0, addr = 0, port = 0, ifname = /var/tmp/cm_snmp_ctrl List = (nil)
Cntl Entry created
pcd: (192): Starting process /usr/sbin/upstream_manager (Rule DOCSIS_USMNGR1).
pcd: (192): Starting process /usr/sbin/upstream_manager (Rule DOCSIS_USMNGR2).
pcd: (192): Starting process /usr/sbin/upstream_manager (Rule DOCSIS_USMNGR3).
pcd: (192): Starting process /usr/sbin/upstream_manager (Rule DOCSIS_USMNGR4).
pcd: (192): Rule DOCSIS_USMNGR4: Success (Process /usr/sbin/upstream_manager (1700)).
pcd: (192): Rule DOCSIS_USMNGR1: Success (Process /usr/sbin/upstream_manager (1697)).
pcd: (192): Rule DOCSIS_USMNGR2: Success (Process /usr/sbin/upstream_manager (1698)).
pcd: (192): Rule DOCSIS_USMNGR3: Success (Process /usr/sbin/upstream_manager (1699)).
pcd: (192): Rule DOCSIS_MACDRIVER: Success (Process /usr/sbin/docsis_mac_driver (1675)).
pcd: (192): Rule DOCSIS_SNMPAGENT: Success (Process /usr/sbin/snmp_agent_cm (1659)).
SNMPA_CreateSocketEntry : type 1, addr = c0a86401, port = 161, ifname = eth0:1 List = 0x9a190
SNMPA_CreateSocketEntry : type 1, addr = c0a86401, port = 162, ifname = eth0:1 List = 0x9a190
pcd: (192): Starting process /usr/sbin/eventmgr_cm (Rule DOCSIS_EVENTMNGR).
pcd: (192): Rule DOCSIS_EVENTMNGR: Success (Process /usr/sbin/eventmgr_cm (2069)).
pcd: (192): Starting process /usr/sbin/docsis_mac_manager (Rule DOCSIS_MACMANAGER).
pcd: (192): Rule DOCSIS_MACMANAGER: Success (Process /usr/sbin/docsis_mac_manager (2070)).
pcd: (192): Starting process /usr/sbin/factd (Rule MOTO_FACTD).
pcd: (192): Rule MOTO_FACTD: Success (Process /usr/sbin/factd (2071)).
pcd: (192): Rule DOCSIS_LASTRULE: Success.
pcd: (192): Starting process insmod (Rule VFE_IPTV_BRIDGE).
pcd: (192): Starting process insmod (Rule PACM_MTANI).

IPTV Bridge char device init done
pcd: (192): Rule VFE_IPTV_BRIDGE: Success (Process insmod (2072)).
pcd: (192): Starting process /bin/sh (Rule VFE_IPTV_BRIDGE_DEV).
mtani: Network interface initialized successfully
Autoconfiguration disabled for esafe0
mtani: Network interface registered successfully
pcd: (192): Rule PACM_MTANI: Success (Process insmod (2073)).
pcd: (192): Starting process /usr/sbin/pacm_init (Rule PACM_INIT).
pcd: (192): Rule VFE_IPTV_BRIDGE_DEV: Success (Process /bin/sh (2131)).
pcd: (192): Starting process /usr/sbin/vfe_mgr_app (Rule VFE_VMA).
pcd: (192): Rule VFE_VMA: Success (Process /usr/sbin/vfe_mgr_app (2261)).
Autoconfiguration disabled for mta0
Production config saved to NVRAMSTA MAC initialized to <MTA MAC>PACM - Exec PACM_Prov_DbInit
PACM - Exec PACM_MSM_DbInit
PACM - Exec Security_InitDataBase
PACM - Exec SnmpDB_Init
pcd: (192): Rule VFE_LASTRULE: Success.
pcd: (192): Rule PACM_INIT: Success (Process /usr/sbin/pacm_init (2220)).
pcd: (192): Starting process insmod (Rule VOICE_INSMXPMOD).
pcd: (192): Starting process /usr/sbin/pacm_vendor_app (Rule PACM_VENDORAPP).
pcd: (192): Starting process /usr/sbin/pacm_snmp_agent (Rule PACM_SNMP).
pcd: (192): Starting process /usr/sbin/pacm_security (Rule PACM_SECURITY).
pcd: (192): Starting process /usr/sbin/pacm_event_mgr (Rule PACM_EVENTMGR).
pcd: (192): Starting process /usr/sbin/pacm_doim (Rule PACM_DOIM).
MXP_TMR: Calibrating MXP Timer...   Ticks/sec=200
Starting MXP timer
MXP module loaded
pcd: (192): Rule VOICE_INSMXPMOD: Success (Process insmod (2262)).
pcd: (192): Starting process insmod (Rule VOICE_INSMXPMEM).
MXP memory module loaded
pcd: (192): Rule VOICE_INSMXPMEM: Success (Process insmod (2271)).
pcd: (192): Starting process insmod (Rule VOICE_INSDSPMOD).
58: Disabling  PUMAV DSPSS 
61: Taking PUMAV DSPSS IN  RESET 
pcd: (192): Rule PACM_VENDORAPP: Success (Process /usr/sbin/pacm_vendor_app (2263)).
HW_DSP module loaded
pcd: (192): Rule PACM_DOIM: Success (Process /usr/sbin/pacm_doim (2267)).
pcd: (192): Rule VOICE_INSDSPMOD: Success (Process insmod (2392)).
pcd: (192): Starting process insmod (Rule VOICE_INSTELEHAL).
TIUHAL: Finished TDM configuration
TIUHAL using DOCSIS clock source
pcd: (192): Rule VOICE_INSTELEHAL: Success (Process insmod (2619)).
pcd: (192): Starting process udevstart (Rule VOICE_UDEVSTART).
pcd: (192): Rule PACM_EVENTMGR: Success (Process /usr/sbin/pacm_event_mgr (2266)).
jffs2: Too few erase blocks (2)
mount: mounting /dev/mtdblock4 on /nvram1 failed: Invalid argument
umount: can't forcibly umount /nvram1: Invalid argument
pcd: (192): Rule PACM_SECURITY: Success (Process /usr/sbin/pacm_security (2265)).
SNMPA_CreateSocketEntry : type 0, addr = 0, port = 0, ifname = /var/tmp/mta_snmp_ctrl List = (nil)
Cntl Entry created
pcd: (192): Rule VOICE_UDEVSTART: Success (Process udevstart (2626)).
pcd: (192): Starting process /usr/sbin/ggncs (Rule VOICE_GGAPP).
tcb_alloc: task id=1,name=mxproot,busy=1
tcb_alloc: task id=2,name=XSPY,busy=1
tcb_alloc: task id=3,name=XTELNET,busy=1
tcb_alloc: task id=4,name=ROOT,busy=1
Initializing signal_handler
>>>> rootInit <<<<<
Creating Golden Gateway application...
Registered with TIUHAL version 3
TID(M) 0 is VE882XXVBLPTC014

tcb_alloc: task id=5,name=NWIF01,busy=1
tcb_alloc: task id=6,name=DQMM,busy=1
Loading dsp image: /lib/dspimage.ld
tcb_alloc: task id=7,name=DLMM,busy=1
tcb_alloc: task id=8,name=ISU,busy=1
tcb_alloc: task id=9,name=VIM,busy=1
tcb_alloc: task id=10,name=CCU,busy=1
tcb_alloc: task id=11,name=RTCP,busy=1
tcb_alloc: task id=12,name=PMA,busy=1
tcb_alloc: task id=13,name=DEX,busy=1
DSPMOD query DSP address syscall: DSP Start address = 0x87E00000
HW_DSP DSP External Config Register set to: 0x87000000, Start: 0x87E00000
58: Disabling  PUMAV DSPSS 
61: Taking PUMAV DSPSS IN  RESET 
DSP external memory mapped to 0x05158000 (User Sp) = 0x87E00000 (Kernel Sp)
dimhw_init_dsp: dpr_base mapped to 0x04358000 (User sp)
tiuo_hw_init, tcid 0, timeslot 1
Could not open file /nvram/6/slic_cal_data
tiuo_hw_init, tcid 1, timeslot 2
tcb_alloc: task id=14,name=DCMM,busy=1
tcb_alloc: task id=15,name=CPMU,busy=1
tcb_alloc: task id=16,name=xGCP,busy=1
tcb_alloc: task id=17,name=sCPU,busy=1
tcb_alloc: task id=18,name=NMM,busy=1
tcb_alloc: task id=19,name=VOIMFE,busy=1
tcb_free: task id=4, name=ROOT
Attempting to delete TCB: 4
XtDelete called 
lmxp_tcb_free called for 4
58: Disabling  PUMAV DSPSS 
61: Taking PUMAV DSPSS IN  RESET 
pcd: (192): Rule VOICE_GGAPP: Success (Process /usr/sbin/ggncs (2726)).
pcd: (192): Rule VOICE_LASTRULE: Success.
pcd: (192): Rule PACM_SNMP: Success (Process /usr/sbin/pacm_snmp_agent (2264)).
pcd: (192): Rule PACM_INITDONE: Success.
pcd: (192): Starting process /usr/sbin/vendor_psm (Rule PACM_APPPSM).
pcd: (192): Starting process /usr/sbin/pacm_mta_control (Rule PACM_MTACTRL).
pcd: (192): Rule PACM_MTACTRL: Success (Process /usr/sbin/pacm_mta_control (3178)).
pcd: (192): Rule PACM_APPPSM: Success (Process /usr/sbin/vendor_psm (3177)).
pcd: (192): Starting process /usr/sbin/pacm_mot_factory (Rule MOTOPACM_MTA_FACTORY).
pcd: (192): Rule MOTOPACM_MTA_FACTORY: Success (Process /usr/sbin/pacm_mot_factory (3179)).
pcd: (192): Rule PACM_LASTRULE: Success.
58: Enabling  PUMAV DSPSS 
61: Taking PUMAV DSPSS OUT of  RESET 
pcd: (192): Warning: Got READY event, but rule end condition is different.
PCD API: ICC wait return value -768
Select failed: : Interrupted system call
pcd: (192): Starting process /usr/sbin/ti_webserver (Rule MOTO_WEB_HFC).
pcd: (192): Rule MOTO_WEB_HFC: Success (Process /usr/sbin/ti_webserver (3528)).
pcd: (192): Starting process /usr/sbin/ti_webserver (Rule MOTO_WEB_CPE).
pcd: (192): Rule MOTO_WEB_CPE: Success (Process /usr/sbin/ti_webserver (3529)).
**** ---- >>>> cnid_do_rx_complete - name "kworker/0:1", pid 36
<INFO> <6>INPUT:DROP INVALID packet IN=eth0 OUT= MAC=<ETH MAC>:xxxxxxxxxxxxx SRC=http://www.geeksecure.info/browse.php?u=wUhhPybQHESe2zjFnDGWa47gKyY09xjStaKB%2BMms4t223Pg%3D&b=5 DST=192.168.0.1 LEN=40 TOS=0x00 PREC=0x00 TTL=128 ID=28131 DF PROTO=TCP SPT=53426 DPT=80 SEQ=3797998253 ACK=3797998253 WINDOW=0 RES=0x00 RST URGP=0 
<INFO> <6>INPUT:DROP INVALID packet IN=eth0 OUT= MAC=<ETH MAC>:xxxxxxxxxxxxx SRC=http://www.geeksecure.info/browse.php?u=wUhhPybQHESe2zjFnDGWa47gKyY09xjStaKB%2BMms4t223Pg%3D&b=5 DST=192.168.0.1 LEN=40 TOS=0x00 PREC=0x00 TTL=128 ID=28132 DF PROTO=TCP SPT=53426 DPT=80 SEQ=3797998253 ACK=3797998253 WINDOW=0 RES=0x00 RST URGP=0 
<INFO> <6>INPUT:DROP INVALID packet IN=eth0 OUT= MAC=<ETH MAC>:xxxxxxxxxxxxx SRC=http://www.geeksecure.info/browse.php?u=wUhhPybQHESe2zjFnDGWa47gKyY09xjStaKB%2BMms4t223Pg%3D&b=5 DST=192.168.0.1 LEN=40 TOS=0x00 PREC=0x00 TTL=128 ID=28133 DF PROTO=TCP SPT=53426 DPT=80 SEQ=3797998253 ACK=3797998253 WINDOW=0 RES=0x00 RST URGP=0 
ARPING to 192.168.100.1 from 192.168.100.1 via eth0
pcd: (192): Starting process /usr/sbin/dmg_provisioning (Rule DOCSIS_DMGPROV).
pcd: (192): Rule DOCSIS_DMGPROV: Success (Process /usr/sbin/dmg_provisioning (5268)).
[INFO] [DOCSIS.PROV(pid=5268)]: DOCSIS provisioning Got SIGCHLD, from pid = -1
[INFO] [DOCSIS.PROV(pid=5268)]: DOCSIS provisioning Got SIGCHLD, from pid = -1
[INFO] [DOCSIS.PROV(pid=5268)]: DOCSIS provisioning Got SIGCHLD,Autoconfiguration disabled for wan0
 from pid = -1
pcd: (192): Starting process /sbin/ti_udhcpc (Rule DOCSIS_DHCPV4).
pcd: (192): Rule DOCSIS_DHCPV4: Success (Process /sbin/ti_udhcpc (5447)).
debug, default_plugin_init

info, Plugin UDHCPC Default registered successfully

info, Plugin Sample registered successfully

info, TI udhcp client (v1.0) started
info, TI udhcp client read_interface, udhcp_client_config.ifindex = 9
debug, entering raw listen mode
***r: must add SUBTLV_CM_CAP_EXT_US_POWER later
info, udhcpc_get_stats
debug, Sending discover...
debug, found a plugin option

debug, found a plugin option

info, udhcpc_get_stats
***r: must add SUBTLV_CM_CAP_EXT_US_POWER later
info, udhcpc_get_stats
debug, Sending select for 10.182.220.58...
Sent 3 probe(s) (3 broadcast(s))
Received 0 reply (0 request(s), 0 broadcast(s))
debug, found a plugin option

debug, found a plugin option

pcd: (192): Starting process /bin/sh (Rule CBN_TELNETD).
pcd: (192): Rule CBN_TELNETD: Success (Process /bin/sh (5795)).
pcd: (192): Starting process /bin/sh (Rule CBN_SSHD).
pcd: (192): Rule CBN_SSHD: Success (Process /bin/sh (5796)).
The process sshd is already killed for wan0
The process sshd is already killed for wan0
telnetd: starting
  port: 23; interface: wan0; login program: /usr/sbin/motlogin
NAT Table update all sessions flushed
NAT Table update all sessions flushed
SNMPA_CreateSocketEntry : type 1, addr = ab6dc3a, port = 161, ifname = wan0 List = 0x9a190
SNMPA_CreateSocketEntry : type 1, addr = ab6dc3a, port = 162, ifname = wan0 List = 0x9a190
info, udhcpc_get_stats
info, No DHCP_T2 option, by default T2=lease * 0.875

debug, DHCP_T2 selected=371980

info, No DHCP_T1 option, by default T1=lease/2

debug, entering none listen mode
Info, default_plugin_init

Info, Plugin TI_TODC Default registered successfully

Info, Plugin libdocsis_todplg.so registered successfully

TI ToD client (v1.0) started 
Info, EVENT:startup

Info, Curr time from xxxxxxxxxxx: Sat Jan 18 17:44:45 2014
 

Info, EVENT:Successfully retrieved time from TOD Server

[CBN_LIM_APP] Update time: Sat Jan 18 17:44:45 2014

[INFO] [DOCSIS.PROV(pid=5816)]: DOCSIS provisioning Got SIGCHLD, from pid = -1
[INFO] [DOCSIS.PROV(pid=5268)]: DOCSIS provisioning Got SIGCHLD, from pid = 5816
getting from <Bootfile TFTP IP-Address>:<CM Bootfile> to <CM Bootfile> [octet]
Received 3236 bytes in 1.0 seconds [25888 bits/sec]
[INFO] [DOCSIS.PROV(pid=6035)]: DOCSIS provisioning Got SIGCHLD, from pid = -1
[INFO] [DOCSIS.PROV(pid=5268)]: DOCSIS provisioning Got SIGCHLD, from pid = 6035
Snmp_SetConfigFile completed with status 0
pcd: (192): Terminating process /bin/sh (5795) (Rule CBN_TELNETD).
pcd: (192): Starting process /bin/sh (Rule CBN_TELNETD).
pcd: (192): Rule CBN_TELNETD: Success (Process /bin/sh (6167)).
pcd: (192): Starting process /bin/sh (Rule CBN_SSHD).
The process telnetd is already killed for eth0
pcd: (192): Rule CBN_SSHD: Success (Process /bin/sh (6168)).
The process sshd is already killed for eth0
pcd: (192): Starting process /bin/sh (Rule CBN_TELNETD).
The process telnetd is already killed for eth0
pcd: (192): Rule CBN_TELNETD: Success (Process /bin/sh (6169)).
pcd: (192): Starting process /bin/sh (Rule CBN_SSHD).
The process sshd is already killed for eth0
pcd: (192): Rule CBN_SSHD: Success (Process /bin/sh (6170)).
pcd: (192): Warning: Cannot stop process, no process is associated with rule CBN_TELNETD.
PCD API: ICC wait return value -518
PCD API: ICC wait return value -520
killall: cm_radius_relay: no process killed
killall: gw_radius_relay: no process killed
Snmp_SetConfigFile completed with status 0
***r: must add SUBTLV_CM_CAP_EXT_US_POWER later
pcd: (192): Starting process /usr/sbin/cbn_update_iptables (Rule CBN_UPDATE_IPTABLES).
pcd: (192): Rule CBN_UPDATE_IPTABLES: Success (Process /usr/sbin/cbn_update_iptables (6350)).
retrieve CbnGwDbEntries1 success
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: iptables -t nat -F wan_prerouting_dmz 2> /dev/null
NAT Table update all sessions flushed
CBN: iptables -F forwarding_wan_dmz 2> /dev/null
NAT Table update all sessions flushed
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: iptables -t nat -F wan_prerouting_portforward 2> /dev/null
NAT Table update all sessions flushed
CBN: iptables -F forwarding_wan_portforward 2> /dev/null
NAT Table update all sessions flushed
CBN: iptables -t nat -F prerouting_lan.vs 2> /dev/null
NAT Table update all sessions flushed
CBN: iptables -F forwarding_lan.vs 2> /dev/null
NAT Table update all sessions flushed
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: iptables -t nat -F forwarding_lan.ipfilter 2> /dev/null
CBN: iptables -F forwarding_lan.ipfilter 2> /dev/null
NAT Table update all sessions flushed
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: iptables -t filter -F lan.macfiltering 2> /dev/null
NAT Table update all sessions flushed
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: iptables -t nat -F forwarding_lan.portfilter 2> /dev/null
CBN: iptables -F forwarding_lan.portfilter 2> /dev/null
NAT Table update all sessions flushed
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: iptables -t nat -F prerouting_lan.ptrigger 2> /dev/null
NAT Table update all sessions flushed
CBN: iptables -t nat -F wan_prerouting_porttrigger 2> /dev/null
NAT Table update all sessions flushed
CBN: iptables -F forwarding_wan_porttrigger 2> /dev/null
NAT Table update all sessions flushed
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: ip6tables -F forwarding_wan.ipfilter 2> /dev/null
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: ip6tables -F forwarding_lan.ipfilter 2> /dev/null
retrieve CbnGwDbEntries1 success
retrieve CBN_VLAN_DB_RetrieveAccess success
retrieve CBN_GRETUNNEL_DB_RetrieveAccess success
CBN:ebtables -t broute -F BROUTING
DEBUG: Register selective packet handler successful
register ingress Hook on  eth0 
warning: configure ingress hook fail no usb dev (null) 
HAL_MacDsUnicastDataFilterAdd: system_rev = 1
No entry in eSafe Dbridge DB for device: wan0
pcd: (192): Starting process /sbin/ti_udhcpc (Rule PACM_DHCP).
debug, default_plugin_init

info, Plugin UDHCPC Default registered successfully

pcd: (192): Rule PACM_DHCP: Success (Process /sbin/ti_udhcpc (6911)).
info, Plugin PacmProv registered successfully

info, TI udhcp client (v1.0) started
info, TI udhcp client read_interface, udhcp_client_config.ifindex = 11
debug, entering raw listen mode
debug, Sending discover...
killall: cm_radius_relay: no process killed
Autoconfiguration disabled for lbr0
HAL_MacDsUnicastDataFilterAdd: system_rev = 1
debug, Sending discover...
debug, found a plugin option

pcd: (192): Starting process /sbin/ti_dhcp6c (Rule DOCSIS_GWDHCPV6).
pcd: (192): Rule DOCSIS_GWDHCPV6: Success (Process /sbin/ti_dhcp6c (8299)).
debug, Sending select for 10.180.211.44...
TI dhcpv6 client (v1.0) started 
Jan/18/2014 17:44:58: dhcp6_reset_timer: reset a timer on lbr0, state=INIT, timeo=0, retrans=277
Jan/18/2014 17:44:58: client6_timo: Going to call plugin init options
Jan/18/2014 17:44:58: ti_dhcp6c_copy_option:  rapid commit (len 0)
Jan/18/2014 17:44:58: ti_dhcp6c_copy_option:  IA_PD (len 12)
Jan/18/2014 17:44:58: ti_dhcp6c_copy_option:  IA_PD prefix (len 25)
Jan/18/2014 17:44:58: ti_dhcp6c_copy_option:  client ID (len 10)
Jan/18/2014 17:44:58: ti_dhcp6c_copy_option:  identity association (len 12)
Jan/18/2014 17:44:58: ti_dhcp6c_copy_option:  IA address (len 24)
Jan/18/2014 17:44:58: client6_timo: After init options: pluginbuf_start: 0xee4e8b0 len: 107
Jan/18/2014 17:44:58: dhcp6_xfer_options: xfer DHCP option rapid commit, len 0
Jan/18/2014 17:44:58: dhcp6_xfer_options: xfer DHCP option IA_PD, len 41
Jan/18/2014 17:44:58:   IA_PD: ID=xxxxxxxxxxxxx, T1=0, T2=0
Jan/18/2014 17:44:58: xferin_option: xferin DHCP option IA_PD prefix, len 25
Jan/18/2014 17:44:58: xferin_option:   IA_PD prefix: ::/62 pltime=0 vltime=0
Jan/18/2014 17:44:58: dhcp6_xfer_options: xfer DHCP option client ID, len 10
Jan/18/2014 17:44:58:   DUID: 00:03:00:01:<GW MAC>
Jan/18/2014 17:44:58: dhcp6_xfer_options: xfer DHCP option identity association, len 40
Jan/18/2014 17:44:58:   IA_NA: ID=xxxxxxxxxxxxx, T1=0, T2=0
Jan/18/2014 17:44:58: xferin_option: xferin DHCP option IA address, len 24
Jan/18/2014 17:44:58: xferin_option:   IA_NA address: :: pltime=0 vltime=0
Jan/18/2014 17:44:58: client6_timo: Going to call save_options
Jan/18/2014 17:44:58: client6_send: a new XID (f93a47) is generated
Jan/18/2014 17:44:58: copy_option: set client ID (len 10)
Jan/18/2014 17:44:58: copyout_option: set IA address
Jan/18/2014 17:44:58: copyout_option: set identity association
Jan/18/2014 17:44:58: copy_option: set rapid commit (len 0)
Jan/18/2014 17:44:58: copy_option: set elapsed time (len 2)
Jan/18/2014 17:44:58: copyout_option: set IA_PD prefix
Jan/18/2014 17:44:58: copyout_option: set IA_PD
Jan/18/2014 17:44:58: fill_ti_dhcp6c_params: Adding a IA_PD id: xxxxxxxxxxxxx t1: 0 t2: 0 cnt: 0
Jan/18/2014 17:44:58: fill_ti_dhcp6c_params: Adding a Prefix cnt: 0 pltime: 0 vltime: 0
Jan/18/2014 17:44:58: fill_ti_dhcp6c_params: Adding a IA_NA id: xxxxxxxxxxxxx t1: 0 t2: 0 cnt: 1
Jan/18/2014 17:44:58: fill_ti_dhcp6c_params: Adding an Address cnt: 0 pltime: 0 vltime: 0
Jan/18/2014 17:44:58: client6_send: Going to call plugin add options
Jan/18/2014 17:44:59: ti_dhcp6c_copy_option:  option request (len 8)
Jan/18/2014 17:44:59: ti_dhcp6c_copy_option:  opt_20 (len 0)
Jan/18/2014 17:44:59: ti_dhcp6c_copy_option:  vendor class (len 16)
Jan/18/2014 17:44:59: ti_dhcp6c_copy_option:  vendor specific info (len 175)
Jan/18/2014 17:44:59: client6_send: After plugin add options len: 332 error: 0 
Jan/18/2014 17:44:59: client6_send: send solicit to xxxxxxxx
Jan/18/2014 17:44:59: dhcp6_reset_timer: reset a timer on lbr0, state=SOLICIT, timeo=0, retrans=1083
Jan/18/2014 17:44:59: client6_recv: receive advertise from fe80::1 on lbr0
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option client ID, len 10
Jan/18/2014 17:44:59:   DUID: 00:03:00:01:<GW MAC>
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option server ID, len 14
Jan/18/2014 17:44:59:   DUID: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option identity association, len 40
Jan/18/2014 17:44:59:   IA_NA: ID=xxxxxxxxxxxxx, T1=1080, T2=1728
Jan/18/2014 17:44:59: copyin_option: get DHCP option IA address, len 24
Jan/18/2014 17:44:59: copyin_option:   IA_NA address: xxxxxxxxxxxxxxxxxx pltime=2160 vltime=4860
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option IA_PD, len 41
Jan/18/2014 17:44:59:   IA_PD: ID=xxxxxxxxxxxxx, T1=1087, T2=1739
Jan/18/2014 17:44:59: copyin_option: get DHCP option IA_PD prefix, len 25
Jan/18/2014 17:44:59: copyin_option:   IA_PD prefix: xxxxxxxxxxxxx pltime=2174 vltime=4874
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option opt_20, len 0
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option DNS, len 32
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option AFTR, len 29
Jan/18/2014 17:44:59: client6_recv: DHCPv6 Server Addr of msg advertise: (fe80::1)
Jan/18/2014 17:44:59: client6_recvadvert: server ID: xxxxxxxxxxxxxxxxxxxxx, pref=-1
Jan/18/2014 17:44:59: client6_recvadvert: calling findlistval with stcode: 6 stcode no prefixes
Jan/18/2014 17:44:59: client6_recvadvert: calling findlistval with stcode: 2 stcode no addresses
Jan/18/2014 17:44:59: client6_recvadvert: unexpected advertise
Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 1 option_len: 10
Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 2 option_len: 14
Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 3 option_len: 40
Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 25 option_len: 41
Jan/18/2014 17:44:59: ti_handle_plugin_options: found a plugin option

Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 20 option_len: 0
Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 23 option_len: 32
Jan/18/2014 17:44:59: ti_handle_plugin_options: found a plugin option

Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 64 option_len: 29
Jan/18/2014 17:44:59: ti_handle_plugin_options: found a plugin option

Jan/18/2014 17:44:59: fill_ti_dhcp6c_params: Adding a IA_PD id: xxxxxxxxxxxxx t1: 1087 t2: 1739 cnt: 0
Jan/18/2014 17:44:59: fill_ti_dhcp6c_params: Adding a Prefix cnt: 0 pltime: 2174 vltime: 4874
Jan/18/2014 17:44:59: fill_ti_dhcp6c_params: Adding a IA_NA id: xxxxxxxxxxxxx t1: 1080 t2: 1728 cnt: 1
Jan/18/2014 17:44:59: fill_ti_dhcp6c_params: Adding an Address cnt: 0 pltime: 2160 vltime: 4860
debug, found a plugin option
Jan/18/2014 17:44:59: client6_recvadvert: Plugin accepted the options

Jan/18/2014 17:44:59: client6_recvadvert: reset timer for lbr0 to 0.672000
Jan/18/2014 17:44:59: client6_recv: receive advertise from fe80::1 on lbr0
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option client ID, len 10
Jan/18/2014 17:44:59:   DUID: 00:03:00:01:<GW MAC>
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option server ID, len 14
Jan/18/2014 17:44:59:   DUID: xxxxxxxxxxxxxx
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option identity association, len 40
Jan/18/2014 17:44:59:   IA_NA: ID=xxxxxxxxxxxxx, T1=1350, T2=2160
Jan/18/2014 17:44:59: copyin_option: get DHCP option IA address, len 24
Jan/18/2014 17:44:59: copyin_option:   IA_NA address: xxxxxxxxxxxxxxxxx pltime=2700 vltime=5400
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option IA_PD, len 41
Jan/18/2014 17:44:59:   IA_PD: ID=xxxxxxxxxxxxx, T1=1350, T2=2160
Jan/18/2014 17:44:59: copyin_option: get DHCP option IA_PD prefix, len 25
Jan/18/2014 17:44:59: copyin_option:   IA_PD prefix: xxxxxxxxxxxxxx pltime=2700 vltime=5400
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option opt_20, len 0
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option DNS, len 32
Jan/18/2014 17:44:59: dhcp6_get_options: get DHCP option AFTR, len 29
Jan/18/2014 17:44:59: client6_recv: DHCPv6 Server Addr of msg advertise: (fe80::1)
Jan/18/2014 17:44:59: client6_recvadvert: server ID: xxxxxxxxxxxxxx, pref=-1
Jan/18/2014 17:44:59: client6_recvadvert: calling findlistval with stcode: 6 stcode no prefixes
Jan/18/2014 17:44:59: client6_recvadvert: calling findlistval with stcode: 2 stcode no addresses
Jan/18/2014 17:44:59: client6_recvadvert: unexpected advertise
Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 1 option_len: 10
Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 2 option_len: 14
Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 3 option_len: 40
Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 25 option_len: 41
Jan/18/2014 17:44:59: ti_handle_plugin_options: found a plugin option

Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 20 option_len: 0
Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 23 optionNAT Table update all sessions flushed
_len: 32
Jan/18/2014 17:44:59: ti_handle_plugin_options: found a plugin option

Jan/18/2014 17:44:59: ti_handle_plugin_options: option code: 64 option_len: 29
Jan/18/2014 17:44:59: ti_handle_plugin_options: found a plugin option

Jan/18/2014 17:44:59: fill_ti_dhcp6c_params: Adding a IA_PD id: xxxxxxxxxxxxx t1: 1350 t2: 2160 cnt: 0
Jan/18/2014 17:44:59: fill_ti_dhcp6c_params: Adding a Prefix cnt: 0 pltime: 2700 vltime: 5400
Jan/18/2014 17:44:59: fill_ti_dhcp6c_params: Adding a IA_NA id: xxxxxxxxxxxxx t1: 1350 t2: 2160 cnt: 1
Jan/18/2014 17:44:59: fill_ti_dhcp6c_params: Adding an Address cnt: 0 pltime: 2700 vltime: 5400
Jan/18/2014 17:44:59: client6_recvadvert: Plugin accepted NAT Table update all sessions flushed
the options
NAT Table update all sessions flushed
tcb_alloc: task id=4,name=ttl1,busy=1
info, No DHCP_T2 option, by default T2=lease * 0.875

debug, DHCP_T2 selected=386878

info, No DHCP_T1 option, by default T1=lease/2

debug, entering none listen mode

*************test_poll_period hit threshold 40ms 1st time
SNMPA_CreateSocketEntry : type 1, addr = ab4d32c, port = 161, ifname = mta0 List = 0x5a7f8
SNMPA_CreateSocketEntry : type 1, addr = ab4d32c, port = 162, ifname = mta0 List = 0x5a7f8
Jan/18/2014 17:45:00: select_server: picked a server (ID: xxxxxxxxxxxxxx)
Jan/18/2014 17:45:00: client6_send: a new XID (1ba728) is generated
Jan/18/2014 17:45:00: copy_option: set client ID (len 10)
Jan/18/2014 17:45:00: copy_option: set server ID (len 14)
Jan/18/2014 17:45:00: copyout_option: set IA address
Jan/18/2014 17:45:00: copyout_option: set identity association
Jan/18/2014 17:45:00: copy_option: set elapsed time (len 2)
Jan/18/2014 17:45:00: copyout_option: set IA_PD prefix
Jan/18/2014 17:45:00: copyout_option: set IA_PD
Jan/18/2014 17:45:00: fill_ti_dhcp6c_params: Adding a IA_PD id: xxxxxxxxxxxxx t1: 0 t2: 0 cnt: 0
Jan/18/2014 17:45:00: fill_ti_dhcp6c_params: Adding a Prefix cnt: 0 pltime: 2700 vltime: 5400
Jan/18/2014 17:45:00: fill_ti_dhcp6c_params: Adding a IA_NA id: xxxxxxxxxxxxx t1: 0 t2: 0 cnt: 1
Jan/18/2014 17:45:00: fill_ti_dhcp6c_params: Adding an Address cnt: 0 pltime: 2700 vltime: 5400
Jan/18/2014 17:45:00: client6_send: Going to call plugin add options
pcd: (192): Starting process /sbin/ti_tftp (Rule PACM_TFTP).
Jan/18/2014 17:45:00: ti_dhcp6c_copy_option:  option request (len 8)
Jan/18/2014 17:45:00: ti_dhcp6c_copy_option:  opt_20 (len 0)
Jan/18/2014 17:45:00: ti_dhcp6c_copy_option:  vendor class (len 16)
Jan/18/2014 17:45:00: ti_dhcp6c_copy_option:  vendor specific info (len 175)
Jan/18/2014 17:45:00: client6_send: After plugin add options len: 346 error: 0 
Jan/18/2014 17:45:00: client6_send: send request to ff02::1:2
Jan/18/2014 17:45:00: dhcp6_reset_timer: reset a timer on lbr0, state=REQUEST, timeo=0, retrans=959
Jan/18/2014 17:45:00: client6_recv: receive reply from fe80::1 on lbr0
Jan/18/2014 17:45:00: dhcp6_get_options: get DHCP option client ID, len 10
Jan/18/2014 17:45:00:   DUID: 00:03:00:01:<GW MAC>
Jan/18/2014 17:45:00: dhcp6_get_options: get DHCP option server ID, len 14
Jan/18/2014 17:45:00:   DUID: xxxxxxxxxxxxxx
Jan/18/2014 17:45:00: dhcp6_get_options: get DHCP option identity association, len 40
Jan/18/2014 17:45:00:   IA_NA: ID=xxxxxxxxxxxxx, T1=1350, T2=2160
Jan/18/2014 17:45:00: copyin_option: get DHCP option IA address, len 24
Jan/18/2014 17:45:00: copyin_option:   IA_NA address: xxxxxxxxxxxxxx pltime=2700 vltime=5400
Jan/18/2014 17:45:00: dhcp6_get_options: get DHCP option IA_PD, len 41
Jan/18/2014 17:45:00:   IA_PD: ID=xxxxxxxxxxxxx, T1=1350, T2=2160
Jan/18/2014 17:45:00: copyin_option: get DHCP option IA_PD prefix, len 25
Jan/18/2014 17:45:00: copyin_option:   IA_PD prefix: xxxxxxxxxxxxxxxxxxx vltime=5400
Jan/18/2014 17:45:00: dhcp6_get_options: get DHCP option opt_20, len 0
Jan/18/2014 17:45:00: dhcp6_get_options: get DHCP option authentication, len 28
Jan/18/2014 17:45:00:   proto: reconfig, alg: HMAC-MD5, RDM: mono counter, RD: 1a0a 0ee4 0ee4 0ee4
Jan/18/2014 17:45:00:   Reconfig auth type: 1, offset=141 
Jan/18/2014 17:45:00: dhcp6_get_options: get DHCP option DNS, len 32
Jan/18/2014 17:45:00: dhcp6_get_options: get DHCP option AFTR, len 29
Jan/18/2014 17:45:00: client6_recv: DHCPv6 Server Addr of msg reply: (fe80::1)
Jan/18/2014 17:45:00: process_auth: previous RD value is unknown (accept it)
Jan/18/2014 17:45:00: ti_handle_plugin_options: option code: 1 option_len: 10
Jan/18/2014 17:45:00: ti_handle_plugin_options: option code: 2 option_len: 14
Jan/18/2014 17:45:00: ti_handle_plugin_options: option code: 3 option_len: 40
Jan/18/2014 17:45:00: ti_handle_plugin_options: option code: 25 option_len: 41
Jan/18/2014 17:45:00: ti_handle_plugin_options: found a plugin option

Jan/18/2014 17:45:00: ti_handle_plugin_options: option code: 20 option_len: 0
Jan/18/2014 17:45:00: ti_handle_plugin_options: option code: 11 option_len: 28
Jan/18/2014 17:45:00: ti_handle_plugin_options: option code: 23 option_len: 32
Jan/18/2014 17:45:00: ti_handle_plugin_options: found a plugin option

Jan/18/2014 17:45:00: ti_handle_plugin_options: option code: 64 option_len: 29
Jan/18/2014 17:45:00: ti_handle_plugin_options: found a plugin option

Jan/18/2014 17:45:00: fill_ti_dhcp6c_params: Adding a IA_PD id: xxxxxxxxxxxxx t1: 1350 t2: 2160 cnt: 0
Jan/18/2014 17:45:00: fill_ti_dhcp6c_params: Adding a Prefix cnt: 0 pltime: 2700 vltime: 5400
Jan/18/2014 17:45:00: fill_ti_dhcp6c_params: Adding a IA_NA id: xxxxxxxxxxxxx t1: 1350 t2: 2160 cnt: 1
Jan/18/2014 17:45:00: fill_ti_dhcp6c_params: Adding an Address cnt: 0 pltime: 2700 vltime: 5400
getting from <Bootfile TFTP IP-Address>:<MTA Bootfile Name> to <MTA Bootfile Name> [octet]
Received 1359 bytes in 0.0 seconds
pcd: (192): Rule PACM_TFTP: Success (Process /sbin/ti_tftp (8999)).
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
CBN: Set Country to GERMANY_CODE
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0
Snmp_SetConfigFile completed with status 0

Error: an inet address is expected rather than "dev".
killall: ndpwatch: no process killed
pcd: (192): Killing process /bin/sh (5795) (Rule CBN_TELNETD).
killall: dibbler-server: no process killed

sh: missing ]
RTNETLINK answers: No such process
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
| Dibbler - a portable DHCPv6, version 0.8.0 (SERVER, Linux port)
| Authors : Tomasz Mrugalski<thomson(at)klub.com.pl>,Marek Senderski<msend(at)o2.pl>
| Licence : GNU GPL v2 only. Developed at Gdansk University of Technology.
| Homepage: http://klub.com.pl/dhcpv6/
2014.01.18 17:45:06 Server Notice    My pid (9713) is stored in /var/lib/dibbler/server.pid
2014.01.18 17:45:06 Server Notice    Detected iface ip6tnl1/13, MAC=<ip6tnl1 MAC>.
2014.01.18 17:45:06 Server Notice    Detected iface esafe0/12, MAC=00:00:00:00:00:00.
2014.01.18 17:45:06 Server Notice    Detected iface mta0/11, MAC=<MTA MAC>.
2014.01.18 17:45:06 Server Notice    Detected iface br0/10, MAC=<ETH MAC>.
2014.01.18 17:45:06 Server Notice    Detected iface wan0/9, MAC=<HF MAC>.
2014.01.18 17:45:06 Server Notice    Detected iface lan0/8, MAC=<LAN MAC>.
2014.01.18 17:45:06 Server Notice    Detected iface lbr0/7, MAC=5c:35NAT Table update all sessions flushed
:3b:ba:1c:ab.
2014.01.18 17:45:06 Server Notice    Detected iface cni0/6, MAC=<CNI MAC>.
2014.01.18 17:45:06 Server Notice    Detected iface ip6tnl0/5, MAC=00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00.
2014.01.18 17:45:06 Server Notice    Detected iface gre0/4, MAC=00:00:00:00.
2014.01.18 17:45:06 Server Notice    Detected iface tunl0/3, MAC=00:00:00:00.
2014.01.18 17:45:06 Server Notice    Detected iface eth0/2, MAC=<ETH MAC>.
2014.01.18 17:45:06 Server Notice    Detected iface lo/NAT Table update all sessions flushed
1, MAC=00:00:00:00:00:00.
2014.01.18 17:45:06 Server Notice    Parsing /etc/dibbler/server.conf config file...
45:06 Server Debug     0 per-client configurations (exceptions) added.
45:06 Server Debug     Parsing /etc/dibbler/server.conf done.
45:06 Server Info      0NAT Table update all sessions flushed
 client class(es) defined.
45:06 Server Debug     1 interface(s) specified in /etc/dibbler/server.conf
45:06 Server Info      Interface eth0/2 configuration has been loaded.
45:06 Server Notice    Running in stateless mode.
45:06 Server Debug     Bulk-leasequery: enabled=no, TCP port=547, max conns=10, timeout=300
45:06 Server Notice    Unable to open DUID file (server-duid), generating new DUID.
45:06 ServNAT Table update all sessions flushed
er Notice    DUID creation: Generating 24-bytes long link-local+time (duid-llt) DUID.
45:06 Server Notice    DUID creation: generated using ip6tnl1/13 interface.
45:06 Server Info      My DUID is xxxxxxxxxxxxxx:<ip6tnl1 MAC>.
45:06 Server Info      Loading old address database (server-AddrNAT Table update all sessions flushed
Mgr.xml), using built-in routines.
45:06 Server Warning   Unable to open server-AddrMgr.xml.
45:06 Server Warning   Cache: Unable to open cache file server-cache.xml.
45:06 Server Notice    Creating multicast (ff02::1:2) socket on eth0/2 (eth0/2) interface.
45:06 Server Notice    Creating link-local (xxxxxxxxxxxxxxxxxxxx) socket on eth0/2 inNAT Table update all sessions flushed
terface.
45:06 Server Debug     Cache: size set to 1048576 bytes, 1 cache entry size is 87 bytes, so maximum 12052 address-client pair(s) may be cached.
45:06 Server Debug     Increased pools usage: currently 0 address(es) are leased.
45:06 Server Notice    Accepting connections. Next event in 4294967295 second(s).
NAT Table update all sessions flushed
NAT Table update all sessions flushed
NAT Table update all sessions flushed
Jan/18/2014 17:45:07: client6_recvreply: Plugin accepted the options
Jan/18/2014 17:45:07: info_printf: nameserver[0] xxxxxxxxxxxxxxxx
Jan/18/2014 17:45:07: info_printf: nameserver[1] xxxxxxxxxxxxxxxx
Jan/18/2014 17:45:07: info_printf: AFTR server[0] m-wams-af72-1.superkabel.de.
Jan/18/2014 17:45:07: get_ia: make an IA: PD-xxxxxxxxxxxxxxxx
Jan/18/2014 17:45:07: update_prefix: create a prefix xxxxxxxxxxxxxx pltime=2700, vltime=5400
Jan/18/2014 17:45:07: get_ia: make an IA: NA-xxxxxxxxxxxxxxxx
Jan/18/2014 17:45:07: update_address: create an address xxxxxxxxxxxxxxxx pltime=2700, vltime=5400
Jan/18/2014 17:45:07: dhcp6_remove_event: removing an event on lbr0, state=REQUEST
Jan/18/2014 17:45:07: dhcp6_remove_event: removing server (ID: xxxxxxxxxxxxxxx)
Jan/18/2014 17:45:07: dhcp6_remove_event: removing server (ID: xxxxxxxxxxxxxxx)
Jan/18/2014 17:45:07: client6_recvreply: got an expected reply, sleeping.
INFO --> Existing session 255 new session 253.
.....
 
Zuletzt bearbeitet:
Code:
pcd: (192): Starting process /bin/sh (Rule CBN_TELNETD).
pcd: (192): Rule CBN_TELNETD: Success (Process /bin/sh (5795)).
pcd: (192): Starting process /bin/sh (Rule CBN_SSHD).
pcd: (192): Rule CBN_SSHD: Success (Process /bin/sh (5796)).
The process sshd is already killed for wan0
The process sshd is already killed for wan0
telnetd: starting
  port: 23; interface: wan0; login program: /usr/sbin/motlogin

[...]

getting from <Bootfile TFTP IP-Address>:<CM Bootfile> to <CM Bootfile> [octet]
Received 3236 bytes in 1.0 seconds [25888 bits/sec]

[...]

pcd: (192): Terminating process /bin/sh (5795) (Rule CBN_TELNETD).
pcd: (192): Starting process /bin/sh (Rule CBN_TELNETD).
pcd: (192): Rule CBN_TELNETD: Success (Process /bin/sh (6167)).
pcd: (192): Starting process /bin/sh (Rule CBN_SSHD).
The process telnetd is already killed for eth0
pcd: (192): Rule CBN_SSHD: Success (Process /bin/sh (6168)).
The process sshd is already killed for eth0
pcd: (192): Starting process /bin/sh (Rule CBN_TELNETD).
The process telnetd is already killed for eth0
pcd: (192): Rule CBN_TELNETD: Success (Process /bin/sh (6169)).
pcd: (192): Starting process /bin/sh (Rule CBN_SSHD).
The process sshd is already killed for eth0
pcd: (192): Rule CBN_SSHD: Success (Process /bin/sh (6170)).
pcd: (192): Warning: Cannot stop process, no process is associated with rule CBN_TELNETD.

[...]

pcd: (192): Starting process /usr/sbin/cbn_update_iptables (Rule CBN_UPDATE_IPTABLES).
pcd: (192): Rule CBN_UPDATE_IPTABLES: Success (Process /usr/sbin/cbn_update_iptables (6350)).
retrieve CbnGwDbEntries1 success
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: iptables -t nat -F wan_prerouting_dmz 2> /dev/null
NAT Table update all sessions flushed
CBN: iptables -F forwarding_wan_dmz 2> /dev/null
NAT Table update all sessions flushed
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: iptables -t nat -F wan_prerouting_portforward 2> /dev/null
NAT Table update all sessions flushed
CBN: iptables -F forwarding_wan_portforward 2> /dev/null
NAT Table update all sessions flushed
CBN: iptables -t nat -F prerouting_lan.vs 2> /dev/null
NAT Table update all sessions flushed
CBN: iptables -F forwarding_lan.vs 2> /dev/null
NAT Table update all sessions flushed
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: iptables -t nat -F forwarding_lan.ipfilter 2> /dev/null
CBN: iptables -F forwarding_lan.ipfilter 2> /dev/null
NAT Table update all sessions flushed
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: iptables -t filter -F lan.macfiltering 2> /dev/null
NAT Table update all sessions flushed
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: iptables -t nat -F forwarding_lan.portfilter 2> /dev/null
CBN: iptables -F forwarding_lan.portfilter 2> /dev/null
NAT Table update all sessions flushed
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: iptables -t nat -F prerouting_lan.ptrigger 2> /dev/null
NAT Table update all sessions flushed
CBN: iptables -t nat -F wan_prerouting_porttrigger 2> /dev/null
NAT Table update all sessions flushed
CBN: iptables -F forwarding_wan_porttrigger 2> /dev/null
NAT Table update all sessions flushed
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: ip6tables -F forwarding_wan.ipfilter 2> /dev/null
Write /var/gwconfig/etc/config/firewall Success
Write /var/gwconfig/etc/config/macfilter Success
Write /var/gwconfig/etc/config/advanced-firewall Success
Write /var/gwconfig/etc/config/ddns Success
CBN: ip6tables -F forwarding_lan.ipfilter 2> /dev/null
retrieve CbnGwDbEntries1 success
retrieve CBN_VLAN_DB_RetrieveAccess success
retrieve CBN_GRETUNNEL_DB_RetrieveAccess success
CBN:ebtables -t broute -F BROUTING

[...]

getting from <Bootfile TFTP IP-Address>:<MTA Bootfile Name> to <MTA Bootfile Name> [octet]
Received 1359 bytes in 0.0 seconds
pcd: (192): Rule PACM_TFTP: Success (Process /sbin/ti_tftp (8999)).
Snmp_SetConfigFile completed with status 0
CBN: Set Country to GERMANY_CODE


Error: an inet address is expected rather than "dev".
killall: ndpwatch: no process killed
pcd: (192): Killing process /bin/sh (5795) (Rule CBN_TELNETD).
killall: dibbler-server: no process killed

sh: missing ]

[...]
Interessante Dinge werden da ausgespuckt. So wie es aussieht existieren SSH und Telnet. Sie werden sogar kurzzeitig aktiviert aber dann wieder gekillt. Vielleicht genug zeit um auf die Maschine zu kommen ?

Die offensichtlichen GPL-Verletzungen sind natürlich auch wieder dabei.
Code:
Dibbler - a portable DHCPv6, version 0.8.0 (SERVER, Linux port)
| Authors : Tomasz Mrugalski<thomson(at)klub.com.pl>,Marek Senderski<msend(at)o2.pl>
| Licence : GNU GPL v2 only. Developed at Gdansk University of Technology.
 
Zuletzt bearbeitet:
Ich habe bereits versucht mit einem TFTP-Client von meinem PC aus die Boot-/Configfile herunterzuladen, was leider nicht glückte (timeout). Das ist wohl nur vom Gerät selber möglich.

Folgende XMLs habe ich gefunden. Nicht besonders interessant, aber der vollständigkeit halber stelle ich das hier mal rein. Das Webinterface verwendet manche davon, bzw. zeigt das Webinterface daraus Daten an. Da manche Seiten jedoch nicht aufrufbar sind, findet man in manchen XMLs bislang unbekannte Sachen. Z.B. die Call History in "xml/MtaCallHistory.xml".

config/LANG.xml
xml/AdvLineProvisioning.xml
xml/AdvSignalingLogs.xml
xml/CmgwBasicSetup.xml
xml/CmgwLogin.xml
xml/CmIndex.xml
xml/CmSystemInformation.xml
xml/CmSystemStatus.xml
xml/DocsisConfigFile.xml
xml/GlobalSettings.xml
xml/LineCallStatus.xml
xml/MtaCallHistory.xml
xml/MtaInit.xml
xml/MtaLineStatus.xml
xml/MtaLogs.xml
xml/PkDhcp.xml
xml/ProvisioningCallFeatures.xml
xml/ProvisioningError.xml
xml/Qos.xmlgl
 
Hallo,

entschuldigt, das ich hier eine Leiche ausgrabe, aber versuche gerade ein wenig über das CH6640E herauszufinden und wollte hanley fragen, welche Ports Tx und Rx sind, hab herausgefunden, das pin1 3,2v hat und pin2 evtl GND ist, aber ich bekomme keine anzeige bei den pins 3 und 4 auf J4

Gruss, Dierk
 
Zurück
Oben