Knoppix Fn+F1

S

Sr01

0
Hallo habe heute die DVD Knoppix 6.3 geschenkt bekommen soweit alles gut.
Wenn ich nun die Tasten Fn+F1 für das Wlan anstellen will nimmt er dieses aber nicht an.

Netzwerkkarte gefunden und die Wlankarte auch gefunden, sollte es nun an den Treibern liegen, nur welchen brauche ich und woher bekomme ich einen?

Laptop Amilo Li2727

Wäre schön wenn mir einer weiterhelfen kann?
 
Könntest du bitte mal nach dem Anschalten des WLAN ein Terminal öffnen und dort "dmesg" eingeben? Die letzten 20 oder 30 Zeilen davon kannst du dann hier pasten, eventuell fehlt ja einfach nur die Firmware.
 
Klar, das ist alles was drin steht:

Code: 
.935390] scsi4 : ata_piix
[    0.936247] ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
[    0.936251] ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
[    0.939176] Error: Driver 'pata_platform' is already registered, aborting...
[    0.939370] PPP generic driver version 2.4.2
[    0.939747] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.939788] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.939813] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[    0.939818] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    0.939944] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    0.939983] ehci_hcd 0000:00:1a.7: debug port 1
[    0.943885] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[    0.943906] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfc404800
[    0.957520] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    0.957548] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.957553] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.957556] usb usb1: Product: EHCI Host Controller
[    0.957559] usb usb1: Manufacturer: Linux 2.6.32.6 ehci_hcd
[    0.957562] usb usb1: SerialNumber: 0000:00:1a.7
[    0.957715] usb usb1: configuration #1 chosen from 1 choice
[    0.957790] hub 1-0:1.0: USB hub found
[    0.957800] hub 1-0:1.0: 4 ports detected
[    0.957885]   alloc irq_desc for 23 on node -1
[    0.957888]   alloc kstat_irqs on node -1
[    0.957897] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    0.957918] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    0.957922] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    0.958039] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    0.958074] ehci_hcd 0000:00:1d.7: debug port 1
[    0.961951] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    0.961970] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc404c00
[    0.973362] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.973384] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    0.973388] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.973391] usb usb2: Product: EHCI Host Controller
[    0.973394] usb usb2: Manufacturer: Linux 2.6.32.6 ehci_hcd
[    0.973397] usb usb2: SerialNumber: 0000:00:1d.7
[    0.973522] usb usb2: configuration #1 chosen from 1 choice
[    0.973600] hub 2-0:1.0: USB hub found
[    0.973609] hub 2-0:1.0: 6 ports detected
[    0.973733] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.973805] uhci_hcd: USB Universal Host Controller Interface driver
[    0.973848] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.973858] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[    0.973862] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    0.973975] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    0.974019] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820
[    0.974065] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    0.974069] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.974072] usb usb3: Product: UHCI Host Controller
[    0.974075] usb usb3: Manufacturer: Linux 2.6.32.6 uhci_hcd
[    0.974078] usb usb3: SerialNumber: 0000:00:1a.0
[    0.974207] usb usb3: configuration #1 chosen from 1 choice
[    0.974284] hub 3-0:1.0: USB hub found
[    0.974293] hub 3-0:1.0: 2 ports detected
[    0.974359]   alloc irq_desc for 21 on node -1
[    0.974362]   alloc kstat_irqs on node -1
[    0.974369] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    0.974380] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    0.974384] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    0.974492] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    0.974535] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840
[    0.974578] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    0.974582] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.974585] usb usb4: Product: UHCI Host Controller
[    0.974588] usb usb4: Manufacturer: Linux 2.6.32.6 uhci_hcd
[    0.974591] usb usb4: SerialNumber: 0000:00:1a.1
[    0.974713] usb usb4: configuration #1 chosen from 1 choice
[    0.974786] hub 4-0:1.0: USB hub found
[    0.974798] hub 4-0:1.0: 2 ports detected
[    0.974865] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    0.974874] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    0.974878] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.974982] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[    0.975015] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001860
[    0.975058] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    0.975062] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.975066] usb usb5: Product: UHCI Host Controller
[    0.975068] usb usb5: Manufacturer: Linux 2.6.32.6 uhci_hcd
[    0.975071] usb usb5: SerialNumber: 0000:00:1d.0
[    0.975193] usb usb5: configuration #1 chosen from 1 choice
[    0.975265] hub 5-0:1.0: USB hub found
[    0.975273] hub 5-0:1.0: 2 ports detected
[    0.975338] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.975347] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    0.975351] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.975459] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[    0.975503] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001880
[    0.975545] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    0.975549] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.975553] usb usb6: Product: UHCI Host Controller
[    0.975556] usb usb6: Manufacturer: Linux 2.6.32.6 uhci_hcd
[    0.975558] usb usb6: SerialNumber: 0000:00:1d.1
[    0.975686] usb usb6: configuration #1 chosen from 1 choice
[    0.975757] hub 6-0:1.0: USB hub found
[    0.975766] hub 6-0:1.0: 2 ports detected
[    0.975833] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.975841] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    0.975846] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.975948] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[    0.975982] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018a0
[    0.976023] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    0.976027] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.976030] usb usb7: Product: UHCI Host Controller
[    0.976033] usb usb7: Manufacturer: Linux 2.6.32.6 uhci_hcd
[    0.976036] usb usb7: SerialNumber: 0000:00:1d.2
[    0.976156] usb usb7: configuration #1 chosen from 1 choice
[    0.976235] hub 7-0:1.0: USB hub found
[    0.976243] hub 7-0:1.0: 2 ports detected
[    0.976453] Initializing USB Mass Storage driver...
[    0.976538] usbcore: registered new interface driver usb-storage
[    0.976542] USB Mass Storage support registered.
[    0.976594] usbcore: registered new interface driver ums-alauda
[    0.976651] usbcore: registered new interface driver ums-cypress
[    0.976721] usbcore: registered new interface driver ums-datafab
[    0.976779] usbcore: registered new interface driver ums-freecom
[    0.976835] usbcore: registered new interface driver ums-isd200
[    0.976889] usbcore: registered new interface driver ums-jumpshot
[    0.976946] usbcore: registered new interface driver ums-karma
[    0.977003] usbcore: registered new interface driver ums-onetouch
[    0.977061] usbcore: registered new interface driver ums-sddr09
[    0.977117] usbcore: registered new interface driver ums-sddr55
[    0.977170] usbcore: registered new interface driver ums-usbat
[    0.977308] PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    0.986517] i8042.c: Detected active multiplexing controller, rev 1.1.
[    0.992794] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.992801] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    0.992805] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    0.992809] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    0.992813] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    0.993121] mice: PS/2 mouse device common for all mice
[    0.993717] rtc_cmos 00:07: RTC can wake from S4
[    0.993828] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[    0.993865] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    0.993975] device-mapper: uevent: version 1.0.3
[    0.994103] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    0.994252] EISA: Probing bus 0 at eisa.0
[    0.994606] cpuidle: using governor ladder
[    0.995183] cpuidle: using governor menu
[    0.995189] ioatdma: Intel(R) QuickData Technology Driver 4.00
[    0.996603] usbcore: registered new interface driver hiddev
[    0.996705] usbcore: registered new interface driver usbhid
[    0.996709] usbhid: v2.6:USB HID core driver
[    0.996829] Advanced Linux Sound Architecture Driver Version 1.0.21.
[    0.997544] ALSA device list:
[    0.997547]   No soundcards found.
[    0.997665] TCP cubic registered
[    0.997667] Initializing XFRM netlink socket
[    0.997673] NET: Registered protocol family 17
[    0.997683] NET: Registered protocol family 15
[    0.997811] lib80211: common routines for IEEE802.11 drivers
[    0.997814] lib80211_crypt: registered algorithm 'NULL'
[    0.998707] Using IPI No-Shortcut mode
[    0.999749] rtc_cmos 00:07: setting system clock to 2010-05-16 17:58:49 UTC (1274032729)
[    1.014036] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[    1.103821] ata4.00: ATAPI: TSSTcorp CDDVDW TS-L632H, fs03, max UDMA/33
[    1.133765] ata4.00: configured for UDMA/33
[    1.268372] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.268390] ata2: SATA link down (SStatus 0 SControl 300)
[    1.268430] ata3: SATA link down (SStatus 0 SControl 300)
[    1.269032] ACPI Warning for \_SB_.PCI0.SATA.PRT0._GTF: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[    1.269042] ata1.00: _GTF unexpected object type 0x1
[    1.317145] ata1.00: ATA-8: WDC WD2500BEVS-22UST0, 01.01A01, max UDMA/133
[    1.317154] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.318307] ata1.00: _GTF unexpected object type 0x1
[    1.318617] ata1.00: configured for UDMA/133
[    1.330275] scsi 0:0:0:0: Direct-Access     ATA      WDC WD2500BEVS-2 01.0 PQ: 0 ANSI: 5
[    1.330873] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[    1.330968] sd 0:0:0:0: [sda] Write Protect is off
[    1.330975] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.331026] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.331069] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.331522]  sda:
[    1.332355] scsi 3:0:0:0: CD-ROM            TSSTcorp CDDVDW TS-L632H  fs03 PQ: 0 ANSI: 5
[    1.335378] sr0: scsi3-mmc drive: 62x/62x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.335385] Uniform CD-ROM driver Revision: 3.20
[    1.335832] sr 3:0:0:0: Attached scsi CD-ROM sr0
[    1.336220] sr 3:0:0:0: Attached scsi generic sg1 type 5
[    1.337284]  sda1 sda2 sda3
[    1.338502] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.338551] Freeing unused kernel memory: 484k freed
[    1.493392] usb 7-1: new low speed USB device using uhci_hcd and address 2
[    1.509700] ISO 9660 Extensions: Microsoft Joliet Level 3
[    1.512035] ISO 9660 Extensions: RRIP_1991A
[    1.640497] cloop: Initializing cloop v2.631
[    1.643929] cloop: loaded (max 8 devices)
[    1.662049] usb 7-1: New USB device found, idVendor=093a, idProduct=2510
[    1.662058] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.662064] usb 7-1: Product: USB OPTICAL MOUSE
[    1.662070] usb 7-1: Manufacturer: PIXART
[    1.662446] usb 7-1: configuration #1 chosen from 1 choice
[    1.689715] input: PIXART USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/input/input6
[    1.690394] generic-usb 0003:093A:2510.0001: input,hidraw0: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-0000:00:1d.2-1/input0
[    1.749642] aufs 2-standalone.tree-31-20090921
[    2.016976] cloop: losetup_file: 70693 blocks, 131072 bytes/block, largest block is 131158 bytes.
[    2.173066] cloop: preloaded 32 blocks into cache.
[    2.192969] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1280b1, caps: 0xa04713/0x204000
[    2.243651] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input7
[    2.248956] ISO 9660 Extensions: RRIP_1991A
[    2.252007] aufs test_add:242:busybox[1575]: uid/gid/perm /KNOPPIX 0/0/0755, 0/0/01777
[   10.503805] cfg80211: Using static regulatory domain info
[   10.503981] cfg80211: Regulatory domain: US
[   10.503984]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.503989]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[   10.503993]     (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[   10.503996]     (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[   10.504000]     (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[   10.504004]     (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[   10.504008]     (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[   10.504016] cfg80211: Calling CRDA for country: US
[   10.584540] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[   10.584553] ACPI: I/O resource 0000:00:1f.3 [0x1c20-0x1c3f] conflicts with ACPI region SMBI [0x1c20-0x1c2f]
[   10.584560] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   10.776122]   alloc irq_desc for 22 on node -1
[   10.776130]   alloc kstat_irqs on node -1
[   10.776144] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   10.776210] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   10.931577] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[   10.931626] r8169 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   10.931709] r8169 0000:02:00.0: setting latency timer to 64
[   10.931815]   alloc irq_desc for 29 on node -1
[   10.931820]   alloc kstat_irqs on node -1
[   10.931846] r8169 0000:02:00.0: irq 29 for MSI/MSI-X
[   10.932062] eth0: RTL8101e at 0xf87c2000, 00:16:d3:8c:3d:81, XID 14000000 IRQ 29
[   11.275107] hda_codec: ALC268: BIOS auto-probing.
[   12.174162] ath5k 0000:08:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[   12.174196] ath5k 0000:08:00.0: setting latency timer to 64
[   12.174245] ath5k 0000:08:00.0: registered as 'phy0'
[   12.675078] ath: EEPROM regdomain: 0x30
[   12.675081] ath: EEPROM indicates we should expect a direct regpair map
[   12.675085] ath: Country alpha2 being used: AM
[   12.675087] ath: Regpair used: 0x30
[   13.313472] phy0: Selected rate control algorithm 'pid'
[   13.313634] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
[   13.313792] cfg80211: Calling CRDA for country: AM
[   29.341300] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input8
[  113.676977] NET: Registered protocol family 10
[  113.677265] lo: Disabled Privacy Extensions
[  134.627808] lp: driver loaded but no devices found
[  134.635811] r8169: eth0: link down
[  134.636195] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  134.659994] ppdev: user-space parallel port driver
[  134.708695] ADDRCONF(NETDEV_UP): wlan0: link is not ready
knoppix@Microknoppix:~$
 
Hallo das ist das was ich bekomme:

iwconfig scan
Code: 
scan      No such device
iwlist scan
Code: 
lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

wlan0     Failed to read scan data : Network is down

Wenn ich mich nicht irre bräuchte ich doch nur einen Treiber und eine Funktion wie ich das WLAN aktiviert bekomme, oder?
 
Ein
Code: 
ifconfig wlan0 up
sollte reichen... Und mit "Ausgabe von ifconfig waere auch gut" meinte ich eigentlich, wirklich nur
Code: 
ifconfig
ohne irgendwelche Parameter.
 
Ok.
ifconfig
Code: 
eth0      Link encap:Ethernet  Hardware Adresse 00:16:d3:8c:3d:81  
          UP BROADCAST MULTICAST  MTU:1500  Metrik:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenlänge:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:29 Basisadresse:0xe000 

lo        Link encap:Lokale Schleife  
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          inet6-Adresse: ::1/128 Gültigkeitsbereich:Maschine
          UP LOOPBACK RUNNING  MTU:16436  Metrik:1
          RX packets:6 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenlänge:0 
          RX bytes:340 (340.0 B)  TX bytes:340 (340.0 B)
 
Hallo, wenn ich nun ifconfig ausführe erscheint mir das:
Und wenn ich dann noch ifconfig wlan0 up ausführe steht dann das da. Mehr schreibt er nicht.(siehe unten)

Geht aber noch immer nicht das Wlan. :(

Code: 
root@Microknoppix:/home/knoppix# ifconfig
eth0      Link encap:Ethernet  Hardware Adresse 00:16:d3:8c:3d:81  
          UP BROADCAST MULTICAST  MTU:1500  Metrik:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenlänge:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:29 Basisadresse:0x6000 

lo        Link encap:Lokale Schleife  
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          inet6-Adresse: ::1/128 Gültigkeitsbereich:Maschine
          UP LOOPBACK RUNNING  MTU:16436  Metrik:1
          RX packets:6 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenlänge:0 
          RX bytes:340 (340.0 B)  TX bytes:340 (340.0 B)

wlan0     Link encap:Ethernet  Hardware Adresse 00:16:44:79:83:6a  
          UP BROADCAST MULTICAST  MTU:1500  Metrik:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenlänge:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

root@Microknoppix:/home/knoppix# ifconfig wlan0 up
root@Microknoppix:/home/knoppix#
 
also nochmal...

erst
Code: 
ifconfig wlan0 up
und dann sollte bei
Code: 
iwlist wlan0 scan
auch was gefunden werden. und wenn er da was findet, dann sollte er auch im wicd (wird doch glaube ich auf den aktuellen Knoppix-CDs als Netzwerk-Manager verwendet, oder?) was finden - und dort kannst du bei dem entsprechenden WLAN auf "Eigenschaften" und kannst deine Verschlüsselung und entsprechenden Key einstellen und dann auf "verbinden" klicken.
(das kannst du zwar auch über die Konsole mit wpa_supplicant machen, aber da du ja anscheinend nicht so mit der Konsole vertraut bist, will ich dir das mal nicht antun ;) )
 
Ok wenn ich es so mache dann:
root@Microknoppix:/home/knoppix# ifconfig wlan0 up
Code: 
SIOCSIFFLAGS: Unbekannter Fehler 132
root@Microknoppix:/home/knoppix# iwlist wlan0 scan
Code: 
wlan0     Interface doesn't support scanning : Network is down

root@Microknoppix:/home/knoppix# NetworkManager restart

Code: 
** (NetworkManager:3350): WARNING **: NetworkManager is already running (pid 3112)

Das ist immer das was ich bekomme.X(
 
Hallo,

Knoppix ist(/war?) eher als Rettungsmedium ausgelegt und bietet darum auch nicht für alle Funktionen integrierte Unterstützung. Je nach Laptopmodell kann man aber Pakete nachinstallieren, welche die Tasten nutzbar machen.

Falls du Linux Einsteiger bist, würd ich dir eher Ubuntu empfehlen. Im Ubuntu-Wiki[1] findest du auch Anleitungen für (fast) alles.

(Bevor jetzt hier ein Glaubenskrieg ausbricht: Ja es gibt sicherlich auch noch andere Distributionen die sich für einen Einsteiger eignen. Aber mein Tipp ist halt nunmal Ubuntu :-))

f.

[1] http://wiki.ubuntuusers.de/
 
Um antworten zu können musst du eingeloggt sein.
Zurück
Oben