Funktion der AUI-Schnittstelle beim Cisco 1603R

Moin!
Ich will meinen 1603R als DSL-Router verwenden. Leider hat der Router nur eine 10BaseT-Schnittstelle; aber es ist noch eine AUI-Schnittstelle vorhanden. Ist das nun eine 10BaseT- oder noch eine ISDN-Schnittstelle?? Aus den Cisco-Dokumten werde ich da net so wirklich schlau und probieren will ich es auch net, da 90V Spannung bei ISDN für eine LAN-Karte doch nicht allzu sehr zu empfehlen sind^^
Ich hoffe, ihr könnt mir da weiterhelfen.

THX,
coolman
 
Also wenn ich es richtig verstanden habe Laut Webseite müßte da ein Extra Kabel bei sein das sich auf mehre Anschlüße aufteilt... Zumindest hab ich das so verstanden...

Ansonsten hast du schon mal auf der Webseite von Cisco geschaut?
Details zur Cisco 1600 Serie

Und wie kommst du auf 90Volt?
 
"Und wie kommst du auf 90Volt?"

An einer ISDN-Schnittstelle liegen immer 90V an, da der geamte ISDN-Bus mit 90V arbeitet (schon sehr oft selbst gefühlt^^).

Die Cisco-Seite kenne ich auch; Problem ist, das dieser Router immer nur mit EINER Lan-schnittstelle angegeben wird; diesen Transceiver auf RJ45 habe ich auch, aber wie gesagt, ich will mir mein Board net zerschießen, wen ich es ausprobiere und da liegen auf einmal 90V an.
 
das ist ein reiner ISDN router.
das AUI und das RJ45, das du siehst, sind ein und der derselbe Anschluß, nämlich ein Ethernet, (zur Innenwelt, Aussenwelt ist wiegesagt ISDN).
An AUI schließt man den Ethernettranceiver seiner Wahl an, also Thick Ethernet, Thin Ethernet, Fiber, oder eben Twisted pair. Und weil twisted pair so häufig war, als der router gebaut wurde, ist der twisted pair tranceiver schon Inklusive.
das ist alles. kein DSL, nur ISDN (und T1 und so was)
 
Um das richtig zu verstehen: die AUI ist eine LAN-Schnittstelle, die ich an meine LAN-Karte im PC anschließen kann?
 
fast.
keine Karte im PC, sondern eine externe "Karte".
An die "Karte" schließt du dann das Ethernet an.
Ethernet kommt in vielen Geschmacksrichtungen, dicke Drähte, dünne Drähte, Koaxial, twisted pair, und für die harten Fälle sogar Glasfaser.
weil man vorher nicht weiß, welches Ethernet du hast, baut man einen genormten Anschluß für alle tranceiver ("Karten").
So war das in den 80ern und 90ern. Heute ist Silizium so billig geworden, daß man eigentlich immer den tranceiver fest mit einbaut, und nebenbei Gehäuse, Netzteil, Stecker einspart. (und der tranceiver, der früher groß wie ein ganzer router war, ist heute nur noch Daumengroß und in irgendeiner Ecke der Platine)

ich sollte wirklich mal ne url suchen, wo solche Hintergründe erklärt sind.
jedenfalls, so wie ich die Cisco PDFs verstehe, ist das dort *kein* WAN Anschluß, sondern einfach der gleich Anschluß, an dem auch der interne twisted pair tranceiver angeschlossen ist. Ob beide gleichzeitig benutzbar sind, also effektiv ein hub, oder einer von beiden abgeschaltet wird, sobald der andere ein Kabel sieht, steht nicht da. Da sie aber sicher den hub lautstark beworben hätten, wenn einer drin wäre, ...
 
Kann jetzt sein, dass ich mich irre, ... aber ich glaub man hat mit vor nem halben Jahr (bin in der Ausbildung zum FISI) erzählt, das wären nur 36V? Habs mir Leider nirgends aufgeschrieben und beim googeln grad auch nichts gefunden, ... weiß das jemand ganau?

?(


(Ps.: Hab die **Volt auch schon zu spüren bekommen :D)
 
@qiubic:
Da lernen wir wahrsch. dasselbe beim gleichen Unternehmen^^
Bin mir sicher, daß es 90V sind. Hatten erst letztens DIV und Meßtechnik.

@hamill:
Wieso WAN-Anschluß?? Man kann doch die Cisco Router-Schnittstellen auf alles mögliche parametrieren (z.B. fa0/0 hört auf PPoE, fa0/1 hört auf TCP/IP usw.). Oder wie jetzt??? Ich bin völlig verwirrt... Und dabei wollte ich doch nur wissen, ob ich mein LAN-Karte zerschieße, wenn ich ein diese mit der AUI verbinde :-((

@ all:
Was mich an der ganzen Sache verunsichert, ist die Tatsache, daß 2 ISDN-Schnittstellen angezeigt werden (es existiert aber nur eine ISDN, eine 10BaseT und eine AUI), bei anderen Routern/Switches die AUI aber immer (die ich kenne)
in ein 10BaseT überführt werden.
Hier mal die sh conf:

Press RETURN to get started!


*Mar 1 00:00:39.164: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
*Mar 1 00:00:39.168: %QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver
problem?
*Mar 1 00:00:39.549: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:00:39.708: %LINK-5-CHANGED: Interface BRI0, changed state to administ
ratively down
*Mar 1 00:00:42.330: %SYS-3-CPUHOG: Task ran for 2152 msec (1/1), process = IPS
EC key engine, PC = 20CDC50.
-Traceback= 218B5AE 218BD56 218F57A 2
*Mar 1 00:00:42.358: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
changed state to down
*Mar 1 00:00:42.362: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0, chan
ged state to down
*Mar 1 00:00:42.362: %LINK-5-CHANGED: Interface Ethernet0, changed state to adm
inistratively down
*Mar 1 00:01:18.249: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-K8OSY-M), Versioright (c) 1986-2004 by cisco Syste
ms, Inc.
Compiled Wed 11-Feb-0
*Mar 1 00:01:18.253: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing
a cold start
Router>#
Router>enable
Router#sh config
Using 5 out of 7506 bytes
end

Router#show int
BRI0 is administratively down, line protocol is down
Hardware is BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 48 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 thro
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
BRI0:1 is administratively down, line protocol is down
Hardware is BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output ne
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 48 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
BRI0:2 is administratively down, line protocol is down
Hardware is BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback no
Keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 48 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Ethernet0 is administratively down, line protocol is down
Hardware is QUICC Ethernet, address is 0030.80f2.7aa8
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 252/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Unknown duplex, Unknown Speed
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:02:08, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/se
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
1 packets output, 60 bytes, 0 underruns
1 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
1 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out

Router#sh run
Building configuration...

Current configuration : 460 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
ip subnet-zero
!
!
!
!
!
!
!
interface Ethernet0
no ip address
shutdown
!
interface BRI0
no ip address
shutdown
!
ip classless
no ip http server
no ip http secure-server
!
!
!
!
line con 0
transport preferred all
transport output all
line vty 0 4
!
!
end

Router#sh version
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-K8OSY-M), Version 12.3(6), RELEASE SOFTWARE (fc3)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Wed 11-Feb-04 16:43 by kellythw
Image text-base: 0x02005000, data-base: 0x02E47B9C

ROM: System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)

Router uptime is 6 minutes
System returned to ROM by power-on
System image file is "flash:c1600-k8osy-mz.123-6.bin"


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco 1603 (68360) processor (revision C) with 23729K/847K bytes of memory.
Processor board ID 16303464, with hardware revision 00000002
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
1 Ethernet/IEEE 802.3 interface(s)
1 ISDN Basic Rate interface(s)
System/IO memory with parity disabled
8192K bytes of DRAM onboard 16384K bytes of DRAM on SIMM
System running from RAM
7K bytes of non-volatile configuration memory.
16384K bytes of processor board PCMCIA flash (Read/Write)

Configuration register is 0x2102
 
Zurück
Oben